Manual Ferm CSM1051 (page 10 of 56) (English, German, Dutch, French)

798918

Zoom out

Zoom in

1/56

8. Screw the Mounting knob (10) into the

threaded screw (16).

9. Pre-tension the saw chain (12) by turning the

screw for the chain quicktensioning system (8)

in the direction.

10. Tighten the mounting knob (10) of the sprocket

cover ( ).

Caution! The pruner saw can be prone

to leaks.

Prior to changing the saw chain, the groove of

the guide rail must be cleaned of dirt because

dirt deposits available can cause the saw chain

to break out of the rail. The deposits can also

absorb the chain oil. So the consequence would

be that the chain oil would not or only a small part

of it would reach the underside of the rail and the

lubrication would be reduced.

Tensioning the saw chain

Regularly tightening the saw chain provides safety

for the user and reduces and/or prevents wear

and chain damages. Before the start of work and

in approx. 10 minute intervals, we recommend the

user to examine the chain tension and correct it,

if necessary. The chain warms up when working

with the saw and thus expands slightly. These

“expansions” can be expected especially from

newer chains.

Do not re-tighten or change the chain

when it is hot because it shrinks slightly

once it has cooled down. In case of non-

observance, this can lead to damages on

the guide rail or the engine because now

the chain is too taut on the blade. Chain

tension and chain lubrication have a

significant impact on the service life of

the chain.

The chain is correctly tensioned if it does not

sag at the rail underside and can be rotated

completely around with the gloved hand. When

the saw chain is tensioned with 9 N (approx. 1 kg),

the gap between the saw chain and the guide rail

may not be more than 2 mm.

10 min 9N max. 2 mm

Switch off the device and remove the

battery before carrying out any

maintenance work.

1. Loosen the mounting knob (10) of the sprocket

cover (9) ( ).

2. To tension the saw chain, turn the screw

(8) for the chain quicktensioning system in the

direction. To loosen the tension, turn the

screw (8) for the quick-tensioning system in

the direction .

3. Tighten the mounting knob (10) of the sprocket

cover (9) again ( ).

The chain tension of a new saw chain

must be readjusted after a maximum of 5

cuts.

Removing/inserting the rechargeable battery

1. To insert the battery (14) into the device,

push the battery along the guide rails into the

device. You will hear them click into place.

2. To remove the battery (14) from the device,

press the release button (14a) on the battery

and pull the battery out.

4. OPERATION

Switch on the chainsaw only when chain

bar, saw chain and sprocket chain wheel

covering are correctly assembled.

Make sure you have a secure stance.

Before starting, ensure that the electric

chainsaw is in contact with no objects.

Never operate the device without the

front cut protection. Risk of injury!

Switching on

1. Place the battery (14) into the device

2. Check the load status of the rechargeable

battery before starting.

3. Hold the device firmly with both hands, with

your right hand on the handle (5) and left hand

on the grip (2). Your thumb and fingers must

tightly clasp the handle (5). Never use the

device onehanded. Risk of injury!

4. To turn on, press the switch lock (3) with your

thumb or index finger and then press the on/

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6.87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1051 Manual

Product: