Manual Ferm CSM1051 (page 8 of 56) (English, German, Dutch, French)

798918

Zoom out

Zoom in

1/56

4 On-off switch with safety chain brake

On releasing the On/Off switch, the device

immediately switches off.

5 Rear grip with hand guard (6)

Protects the hand against branches and boughs

in the case of springing away by the chain.

12 Saw chain with small spring-back

helps you to catch spring-backs with specially

developed control systems.

Warning: The vibration emission value may differ

during actual use of the power tool from the

stated value depending on the manner in which

the power tool is used.

Try to keep the exposure to vibrations as low

as possible. Examples of measures to reduce

vibration exposure are the wearing of gloves when

using the tool and limiting the working hours. All

parts of the operating cycle are to be taken into

account in this (for example times in which the

electric tool is turned off and those in which even

though it is turned on, it is not running under a load)

Beware of kickback! Be careful of

kickback of the machine during work.

There is danger of injury here. You can

avoid kickbacks by exercising caution

and using a correct sawing technique.

Fig. 1

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut (cf. fi

g 1/image B). Tip contact in some cases may cause

a sudden reverse reaction, kicking the guide bar up

and back towards the operator (fig. 1/image A).

Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards

the operator.

Each of these reactions can lead to you losing

control of the saw and potentially being seriously

injured. Do not rely exclusively on the safety

devices built into the pruner saw. As user of

the pruner saw, you should undertake various

measures to enable accident- and injury free

working.

Kickback is the result of tool misuse and/ or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below:

a) Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces.

Kickback forces can be controlled by the

operator, if proper precautions are taken. Do

not let go of the chain saw.

b) Avoid an abnormal work posture and do not

saw above shoulder height. This prevents

unintentional contact with the rail tip and

enables better control of the pruner saw in

unforeseen situations.

c) Only use replacement bars and chains

specified by the manufacturer. Incorrect

replacement bars and chains may cause chain

breakage and/or kickback.

d) Follow the manufacturer´s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

Further safety directions

• Comply carefully with maintenance, control

and service instructions in this manual.

• Damaged protective devices and parts have

to be repaired or changed except as noted

otherwise in this manual.

• It is recommended that a first-time user at

least practice the cutting of logs on a saw log

or frame.

• For sawing work on hillsides, always stand in

the area above the log. To keep total control

while sawing through, reduce the pressure at

the end of the cut without loosening your grip

on the handles of the pruner saw. Make sure

the saw chain does not touch the ground.

After finishing the cut, wait until the pruner

saw comes to a stop before removing it there.

Always switch off the motor of the pruner saw

before changing between trees.

• Dirt, stones, loose bark, nails, clips and wires

must be removed from the tree.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6.87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1051 Manual

Product: