Manual Ferm BSM1010 - FBS400 (page 13 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632791

Zoom out

Zoom in

1/60

Ferm 13

Only use sharp and undamaged saw bands.

Bent saw bands should be replaced immediately.

Always mount the saw band with the teeth pointing down.

Set the correct saw band tension to help avoid breaking the blade.

Adjusting the end stop

Fig. J

The end stop prevents the saw band from touching the base of the machine.

• Turn the end stop (28) in or out to determine the correct adjustment.

Mounting and setting the length stop

Fig. K

The length stop is used for sawing workpieces of the same length.

• Insert the bar (29) into the corresponding hole (30) in the side of the frame.

• Mount the length stop (10) to the bar.

• Set the length stop to the required distance.

• Tighten the knob (31).

Adjusting the sawing angle

Fig. L

The default angle between the saw band and the saw table is 90°.

• Use a set square to check that the angle between the saw band (3) and the table (17) is 90°.

If the angle does not measure 90° adjust as follows:

• Slacken the screw (32) of the lower saw band guide (33) a few threads.

• Adjust the saw band guide so that the saw band is at a right angle with the table.

• Tighten the locking knob.

• Proceed in the same way for adjusting the upper saw band guide (34).

Make sure that the saw band is at a right angle with the table along the entire length

of the table.

Adjusting the straight cross-cut angle

Fig. M

The default angle between the saw band and the fence is 90°.

• Slacken the lock knob (8) a few threads.

• Set the mitre angle to 0°.

• Use a set square to check that the angle between the saw band (3) and the fence (35) is

90°.

4. USE

108

Ferm

• Udfør aldrig udkast-, monterings- eller andre arbejder på bordet, mens maskinen er tændt.

• Sluk for maskinen, og rengør bordet, før du går fra maskinen.

Maskinen skal slukkesøjeblikkeligt, når

• Båndsavmaskinen er overophedet.

• Stikket eller netledningen er defekt, eller hvis ledningen er beskadiget.

• Afbryderen er defekt.

• Der er røg eller det lugter af svedet isolation.

Sikkerhedsforskrifter

Ved anvendelse af elektriske maskiner skal man altid følge de lokalt gældende

sikkerhedsforskrifter i forbindelse med brandfare, fare for elektrisk stød og

legemensbeskadigelse. Læs udover de nedenstående instruktioner også

sikkerhedsforskrifterne i den separat vedlagte sikkerhedsfolder. Bevar instruktionerne godt!

Kontroller altid om netspændingen svarer til værdien på typeskiltet.

Udskiftning af ledninger eller stik

Gamle ledninger og stik skal smides væk, når de er blevet udskiftet med nye. Det er farligt at

sætte stikket på en løs ledning i en stikkontakt.

Brug af forlængerledninger

Brug kun en godkendt forlængerledning, der er egnet til indgangseffekten på maskinen. Det

minimale ledertværsnit er 1,5 mm

.Hvis der bruges ledning på en kabeltromle, skal ledningen

altid rulles helt ud.

Montering af maskinen

Fig. B1 & B2

Maskinen kan sættes op på to måder: til brug på en arbejdsbænk (fig. B1) og til brug med

støtten (fig. B2).

Maskinen fastgøres med skruer på en arbejdsbænk.

Montering af maskinen til brug på en arbejdsbænk:

• Marker befæstigelseshuller (2) på arbejdsbænken.

• Bor på de markerede steder huller med den rigtige diameter og dybde til de skruer, der skal

anvendes.

• Anbring maskinen på arbejdsbænken og stik skruerne gennem befæstigelseshullerne.

• Skru skruerne godt fast.

Montering af maskinen til brug med støtten:

• Følg nedenstående instruktioner i det følgende afsnit ’Samling af stativet’.

• Sæt maskinen på stativet (11).

• Sæt hullerne (12) i stativet ud for befæstigelseshullerne (2).

3. MONTAGE OG INDSTILLINGS FORSKRIFTER

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1010 - FBS400 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BSM1010 - FBS400 Manual

Product: