632791
12
Zoom out
Zoom in
Previous page
1/60
Next page
Ferm 109
Sæt låsene på (13).
Stram låsene.
Samling af stativet
Fig. C1
Maskinen skal placeres på en lige og solid overflade. Brug altid følgende fremgangsmåde, og i
den rækkefølge der er angivet, når du samler maskinen.
Montér bordbenene (14).
Montér de lange støtteskinner (15).
Montér de korte støtteskinner (16).
Stram alle låse.
Sæt stativet opret.
Montering af bordbenene
Fig. C2
Bordbenene skal monteres i overensstemmelse med tallene i hjørnerne på bordfladen.
Hold det første ben (14) på plads mod hjørnet af bordtoppen (17) og spænd det fast med
låsene (18).
Stram ikke låsene helt.
Følg de samme anvisninger, når du monterer de andre ben.
Montering af de lange støtteskinner
Fig. C3
Hold den første skinne (15) på plads mod bordbenet (14), og spænd den fast med låsene
(19).
Stram ikke låsene helt.
Montér den anden skinne på samme måde.
Montering af de korte støtteskinner
Fig. C4
Hold den første skinne (15) på plads mod bordbenet (14), og spænd den fast med låsene
(20).
Stram ikke låsene helt.
Montér den anden skinne på samme måde.
Montering af bordforlængelsen
Fig. D
Løsn skruerne (21).
Hold bordforlængelsen (22) på plads mod bordtoppen (17) og monter skruerne.
Stram skruerne.
Savklingebeskyttelse
Fig. A, E, & F
Savklingebeskyttelsen kan fjernes midlertidigt for at justere og/eller udskifte savklingen.
Løft savklingehylsteret (5) op.
UK
D
NL
F
E
P
I
S
SF
N
DK
12
Ferm
Loosen the screws (23) and remove the cover (6).
Loosen the screws (24) and remove the saw band protection (4).
Replace the saw band protection as soon as the saw band has been adjusted and/or
replaced.
Never use the saw without saw band protection.
Make sure the saw band protection screens as much of the saw band as possible.
Adjusting the saw band
Fig. A, E & G
The saw band has been adjusted correctly when the back of the saw band runs against the
raised edge of the saw band wheels and the band does not show wobble.
Raise the saw band housing (5).
Loosen the screws (23) and remove the cover (6).
Turn the saw band (3) around by turning the upper saw band wheel (25) into the sawing
direction, and check the tension of the saw band.
If adjustment is required, proceed as follows:
Slacken the height adjuster (7) and slide the saw band over the wheel so that the back of
the saw band runs against the raised edge of the wheel.
Check the running of the saw band again and further adjust if required.
Tighten the height adjuster.
Replacing the saw band
Fig. A, H & I
Raise the saw band housing (5).
Loosen the screws (23) and remove the cover (6).
Loosen the screws (24) and remove the saw band protection (4).
Loosen the screws (26) and remove the guides (27).
Remove the old band.
Put the new band (3) round the saw band wheels as shown.
First put the blade round the upper wheel, then, while holding the blade in place,
put it round the lower wheel.
Adjust the band
Tension the saw band.
Replace the guides.
Replace the saw band protection.
Replace the cover and tighten the screws.
Before changing a saw band, always unplug the machine.
GB
D
NL
F
E
P
I
S
SF
N
DK
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BSM1010 - FBS400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1010 - FBS400 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info