Manual Ferm BSM1010 - FBS400 (page 14 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632791

Zoom out

Zoom in

1/60

Ferm 107

Symbolforklaring

Idenne brugervejledninge og/eller på maskinen anvendes der følgende piktogrammer:

Læs instruktionerne omhyggeligt

I overensstemmelse med grundlæggende sikkerhedsstandarder i de europæiske

direktiver.

Betegnelse for risiko for personskader, dødsfald eller beskadigelse af værktøjet i

tilfælde af at du er uopmærksom på instruktioner i denne manual.

indikerer farer for elektrisk stød

hold tilstedeværende på afstand.

Fjern stikket fra kontakten.

Bær beskyttelsesbriller og høreværn

Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres

på en genbrugsplads.

Specifikke sikkerhedsforskrifter

• Under savningen må du aldrig holde fingrene på et sted, hvor de kan komme i kontakt med

savklingen, da der er risiko for, at arbejdsemnet forskydes uventet.

• Sørg for, at savklingen har den rette spænding.

• Sørg for, at savklingen monteres med tænderne nedad for at undgå, at emnet utilsigtet

bliver løftet op.

• Der må ikke benyttes savklinger, som er beregnet til at skære i træ.

• Brug ikke bøjede, deforme eller på anden måde beskadigede savklinger.

• Brug aldrig maskinen til skæring af arbejdsemner af træ.

• Brug ikke maskinen til at save i arbejdsemner af magnesium.

• Begynd aldrig at save, før maskinen er nået op på fuld hastighed.

• Man skal fastspænde arbejdsemnet sikkert. Prøv aldrig at save meget små arbejdsemner.

•

Arbejdsområdet må ikke forlades, før maskinen er slukket og savklingen står helt stille.

•

ag ikke maskinen i brug, før den er færdigmonteret og installeret i henhold til

anvisningerne.

2. SIKKERHEDSFORSKRIFTER

Ferm

If the angle does not measure 90° adjust as follows:

• Loosen the adjusting screw (36) and move the head so the saw band reaches a 90° angle.

• Loosen the locknut (37) on the adjusting screw and screw the adjusting screw in or out to

achieve a 90° angle. Retighten the locknut.

• Tighten the adjusting screw.

• Loosen the screw (38) and adjust the pointer (39) so that it registers 0°. Tighten the screw.

Setting the mitre angle

Fig. M

The mitre angle is infinitely variable between 0° and 45°.

• Slacken the lock knob (8) a few threads.

• Set the required mitre angle using the scale (40).

• Securely tighten the lock knob.

Clamping the workpiece

Fig. N

• Turn the clamp (9) a little further than the thickness of the workpiece using the wheel (41).

• Place the workpiece against the fence (35).

• Tighten the vice using the wheel so the workpiece is clamped tightly between the vice and

the fence.

Always use the vice!

Instructions for use

• Switch on the machine before the workpiece makes contact with the saw band.

• Depress the head with equal force to allow the saw band to cut through the workpiece and

enter the table slot

• Do not exert pressure on the saw band. Allow the machine enough time to cut the

workpiece.

• Best results are achieved with workpieces up to approx. 2.5 cm.

• Be careful when the workpiece is thicker than 2.5 cm.

• To maintain optimum efficiency, replace a worn saw band in time.

• Only raise the saw band housing after the saw band has come to a complete standstill.

Switching on and off

Fig. A

This machine is equipped with a no-volt release feature.

This feature avoids that the machine is accidentally switched on when the plug is inserted into

the mains outlet.

• To switch the machine on, set the on/off switch (1) to ‘I’.

• To switch the machine off, set the on/off switch (1) to ‘0’.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1010 - FBS400 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BSM1010 - FBS400 Manual

Product: