663878
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
This unique 3-Stage design gives you an edge of remarkable sharpness and, because of
the triple angle bevel it creates on each facet, you will note knives stay sharp longer.
The following sections describe the general procedures for optimal sharpening in each
stage and suggest how you can optimize the edge for your intended uses.
Unless you do a lot of heavy duty cutting you will need to use Stage 1 only once in a while.
One of the important advantages of using the EdgeSelect Sharpening Module is that you
can strop and polish your knives to razor sharp edges as often as needed and yet
experience little knife wear compared to older sharpening methods. Resharpening can
usually be done in Stage 3. Occasionally you will need to use Stage 2 for resharpening.
Use Stage 1 only for the heaviest duty applications (see Resharpening Section.)
The Chef’sChoice
®
Model 2100 EdgeSelect Sharpening Module is equipped with a
manually activated diamond dressing accessory that can be used if necessary to remove
any accumulated food or sharpening debris from the surface of the polishing/stropping
disks. In order to minimize the need for dressing, we strongly urge you to clean knives each
time before sharpening them. By doing so, you will be able to go months before you need
to “dress” these disks. Only when you sense a distinct decrease in polishing efficiency will
there by any need to use this convenient feature described further in a subsequent section.
The sharpening and honing disks are spring-loaded on their drive shaft to provide an
optimum sharpening pressure that ensures rapid yet uniform sharpness along the length of
the edge and minimizes the potential for gouging the edge.
Each sharpening Stage is equipped with knife hold down springs that are positioned over
the sharpening disks to provide a spring action that holds the face of your knife securely
against the precision guide planes in the right and left slots of that stage during sharpening.
Unless you have special blades designed to be sharpened primarily on one side of the edge
(such as Japanese Kataba blades) you will want to sharpen equally in the right and left
slots of each stage you use. This will ensure the edge is symmetrical and will cut straight
at all times.
When sharpening in any stage, the knife should, on sequential strokes, be pulled
alternately through the left slot and the right slot of that Stage. Generally only one
pull in the left and one in the right slot will be adequate in each stage; with duller blades
you may need to make two pairs of pulls in a given stage (see subsequent sections for
more detail). Always operate the sharpener from the front side. Hold the blade horizontal
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Commercial 2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Commercial 2100 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info