571631
7
Zoom out
Zoom in
Previous page
1/36
Next page
English
INSTALLATION MANUAL
Follow the procedure described below:
Ø
Disconnect the pipes from the gas control (flexible gas pipe, aluminium pilot burner pipe and thermocouple 1);
!Caution
The red wire of thermocouple 2, if applicable, must remain connected to the gas control.
Ø
Disconnect the gas control from the burner mounting plate by unscrewing the self-tapping screw.
Ø
Carefully unwind the red and black wire of thermocouple 2, if applicable.
Ø
Carefully lay the gas control together with the wires of thermocouple 2, the ignition cable, the flexible gas hose,
the aluminium pilot burner pipe and the type plate plus chain in the direction of the control hatch.
!Caution
Prevent dirt in gas pipes and connections;
Avoid kinks in the pipes.
!Caution
Make sure the ignition cable cannot come into contact with other wires;
The data plate should remain attached to the chain.
Ø
Set the height of the appliance using the adjustable feet (if applicable).
Ø
Make the appliance level at the same time.
!Tip
The construction frame for most 2 or 3 sided appliances can be adjusted. This will allow you to connect the
construction frame to the chimney breast correctly. For 2 or 3 sided appliances that cannot be adjusted, we would
like to refer you to chapter 5.9 'Additional instructions'.
!Caution
do not ignite the appliance before the gas and discharge connections have been fully installed, first observe the
procedure described in chapter 7.3.
5.5Placingthechimneybreast (if applicable)
In order to provide proper heat discharge, there should be sufficient space around the appliance. The chimney
breast should be ventilated sufficiently by means of ventilation holes (incoming and outgoing).
!Caution
Use non combustible and heat-resistant material for the chimney breast, including the top of the chimney
breast, the material inside the chimney breast and the back wall of the chimney breast.
Make sure that the appliance is not carrying the weight of the chimney breast when using stone-like
materials.
The passage of the ventilation holes (outgoing), which are placed as high as possible, is stated in Appendix 2,
Table 2.
!Caution
When placing the chimney breast, you should take the following into account (see Appendix 3, fig. 2):
the location of the control hatch: this must be placed as low as possible;
the dimensions of the control hatch; see Placing the control hatch section 5.6;
the Dru control hatch is not supplied with all appliances. Nevertheless, we recommend only using a Dru
control hatch, if available, exept in the case of B 11 AS/BS appliances. If you decide not to take this option, you
will have to make a 100 cm2 ventilation hole that is placed as low as possible, for the benefit of the incoming
ventilation;
the location of the ventilation holes (V) (outgoing);
maintain a minimum 30 cm distance between the top of the ventilation hole (outgoing) and the ceiling of the
house.
the measurements of the glass pane, so that it can be placed/removed after placing the chimney breast;
the protection of the gas control and the pipes against cement and plaster.
If possible, you should place decorative strips, frames, etc., after any required structural work has been
completed. Avoid the use of painter's tape. If this is not possible: please use good quality painter's tape and
remove it immediately after plastering or painting work has been completed.
!Tip
You should preferably apply the ventilation holes (outgoing) on both sides of the chimney breast. You can use
DRU ventilation elements.
Prior to completely closing the chimney breast, check whether the discharge / concentric system is placed
correctly.
whether the channels, fixing brackets and possible clip bindings, which cannot be reached after installation,
are fastened by means of self-tapping screws.
7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Diablo Next at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Diablo Next in the language / languages: English as an attachment in your email.

The manual is 4.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Diablo Next

DRU Diablo Next User Manual - English - 20 pages

DRU Diablo Next Installation Guide - German - 36 pages

DRU Diablo Next User Manual - German - 20 pages

DRU Diablo Next Installation Guide - Dutch - 36 pages

DRU Diablo Next User Manual - Dutch - 20 pages

DRU Diablo Next User Manual - Dutch - 16 pages

DRU Diablo Next User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info