571631
8
Zoom out
Zoom in
Previous page
1/36
Next page
English
INSTALLATION MANUAL
Ø
If applicable, do not plaster on or over the edges of the construction frame, because:
the heat of the appliance could cause cracks;
it will no longer be possible to remove/place the glass pane.
Ø
When using stone-like materials and/or a plaster finishing, allow the chimney breast to dry for at least six weeks
prior to using the appliance in order to prevent cracks.
5.6Placingthecontrolhatch (if applicable)
The control hatch (also see paragraphs 5.4 and 5.5) is placed as low as possible in the chimney breast.
!Caution
The bottom of the control hatch may not be placed higher in the appliance than the burner surface.
Place control hatch and bracket with gas control and accessories indoors in a dry place only!
A number of components are placed in the control hatch, such as data plate, gas control, receiver belonging to the
remote control and, if applicable, the components belonging to the DRU Powervent system ®.
Place the control hatch as follows; see Appendix 3, fig. 3 for details:
Ø
Make an opening in the chimney breast, as described in the manual for the control hatch.
Ø
Place the inner frame (1); unscrew bolts (5) for this.
!Tip
When the chimney breast is made of bricks, the inner frame can be built with bricks at the same time
When using a different material, you can glue the inner frame or fix it with four flush screws.
Ø
Mount the gas control to the brackets of the inner frame (2).
Ø
Check whether pipes and connections are free from dirt;
Ø
Reconnect the pipes to the gas control.
!Caution
Avoid kinks in the pipes;
Tighten the flexible gas pipe and the pilot burner pipe until they are gastight.
First tighten the thermocouple by hand and;
Then tighten it a quarter turn using a suitable spanner;
The pilot burner pipe must be protected against possible corrosive influences as a result of, for example,
humidity, cement that has fallen down, dirt that has fallen down from the chimney, etc. The pilot burner pipe
should remain permanently free from the ground and the walls of the room in which the appliance is built in.
When installing in an existing fireplace, or if it is not possible to keep the pipes free, the pipe should be
protected against corrosion by means of a jacket.
Ø
Prevent dirt in gas pipes and connections.
Ø
Connect the gas pipe to the gas tap.
Ø
Bleed the gas pipe.
Ø
Place the receiver in the holder (3); for connecting, see section 6.1.
Ø
Place the data plate in its intended clamp (6).
Ø
Fix the outer frame with door (4) to the inner frame using 2 socket cap screws (5).
!Tip
You can place the outer frame in such a way, that the door turns to the left or to the right.
5.7Fluegasdischargesysteminapplianceswithopencombustion
For connection to an existing chimney without a discharge pipe or flexible SS discharge - only allowed in Great
Britain - the instructions provided in the separately supplied booklet 'Fitting into a conventional class 1 chimney'
apply. In addition to the installation instructions, this booklet also contains supplementary tests. In this situation
we recommend using a stainless steel flexible discharge pipe over the complete length, with a draught increasing
hood.
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Diablo Next at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Diablo Next in the language / languages: English as an attachment in your email.

The manual is 4.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Diablo Next

DRU Diablo Next User Manual - English - 20 pages

DRU Diablo Next Installation Guide - German - 36 pages

DRU Diablo Next User Manual - German - 20 pages

DRU Diablo Next Installation Guide - Dutch - 36 pages

DRU Diablo Next User Manual - Dutch - 20 pages

DRU Diablo Next User Manual - Dutch - 16 pages

DRU Diablo Next User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info