519304
12
Zoom out
Zoom in
Previous page
1/24
Next page
DEX
9 Elektroanschluss
(nurdurchdenFachmann)
Electrical connection
(onlybyaspecialist)
Elektroanschluss von oben
1. Öffnen Sie die im oberen
Gerätebereich vorhandene
Sollbruchstelle (S) an der Prägung
durch kräftigen Druck mit einem
stumpfen Werkzeug
(z.B. Schraubendreher).
2. Schneiden Sie die Durchfüh-
rungs tülle (23) entsprechend
dem Zuleitungsquerschnitt auf.
Dabei soll die Öffnung in der
Tülle etwas kleiner als der Quer-
schnitt des Kabels sein, um einen
optimalen Schutz gegen Wasser
zu erzielen. Passen Sie die Tülle in
den Durchbruch ein. Die Schutz-
tülle muss verwendet werden!
3. Manteln Sie das Elektrokabel
ungefähr 6 cm über dem Wand-
austritt ab. Nehmen Sie das
vorbereitete Gerät so in die Hand,
dass Sie mit der anderen Hand das
Kabel in die Gummi tülle führen
können.
4. Setzen Sie das Gerät so auf
den Wandhalter (10), dass die
Gewindestange des Wandhalters
in das vorgesehene Loch des
Gerätes passt.
5. Lösen Sie die Befestigungs-
schraube der Anschlussklemme.
Versetzen Sie die Anschluss-
klemme auf den oberen Fuß.
Befestigen Sie die Anschluss-
klemme dort wieder.
6 Isolieren Sie die Kabel ab und
schließen diese an die Anschluss-
klemmen gemäß des auf S. 10
abgebildeten Schaltplanes an.
Das Gerät ist an den Schutzleiter
anzuschließen.
7. Setzen Sie das Gehäuse auf
das Gerät und drehen Sie die
Befestigungs schraube ein. Danach
können Sie die Blende aufrasten.
Electrical connection from
above
1. Open the prepared breaking
point (S) in the upper part of
the appliance by pressing with
a blunt implement
(e.g. srewdriver).
2. Slit the grommet (23) to match
the cable size. The opening in
the grommet should be slightly
smaller than the cross-section
of the cable in order to ensure
optimum protection against
water. Fit the grommet into
the opening. The protection
grommet must be used!
3. Strip the cable roughly 6 cm
above the point where it emerges
from the wall. Hold the prepared
appliance so that you can route
the cable into the grommet with
the other hand.
4. Place the appliance on the heater
bracket (10) so that the threaded
rod of the wall bracket fits in the
provided hole of the appliance.
5. Unscrew the fastening screw of
the connecting terminal. Displace
the connecting terminal to the
upper foot. Affix the connecting
terminal again.
6. Insulate the cables and plug
them in the connecting terminals
according to the wiring diagram
on page 10.
The appliance must be earthed.
7. Place the hood on the appliance
and screw in the fastening screw.
After that you can reinsert the
faceplate.
S
12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clage DEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clage DEX in the language / languages: English, German as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info