519304
11
Zoom out
Zoom in
Previous page
1/24
Next page
DEX
9 Elektroanschluss
(nurdurchdenFachmann)
Electrical connection
(onlybyaspecialist)
gewünschte Wert (0, 1 oder 2) im Display
erscheint, dann Tasten loslassen. Zunächst
ist die Betriebsart 1 zu wählen und die
Funktion des Lastabwurfrelais bei kleiner
Geräte leistung (35 Grad Sollwert und
geringer Wassermenge) zu prüfen. Kommt
es zu einem Flackern des Abwurfrelais, so
muss die Betriebsart 2 gewählt werden.
Elektroanschluss von unten
1. Manteln Sie das Anschlusskabel
ungefähr 6 cm über dem Wandaustritt
ab. Schieben Sie die Spritzwasser-
schutztülle (22) mit der kleineren
ÖffnungvoranüberdasAnschluss-
kabel, so dass die Schutztülle wand-
bündig abschließt. Diese verhindert,
dass eventuell eindringendes Wasser
mit den Elektroleitungen in Kontakt
kommt. Sie darf nicht beschädigt
sein! Die Schutztülle muss verwendet
werden!
2. Klapphalter (15) nach rechts klappen.
3. Isolieren Sie die Kabel ab und schließen
diese an die Anschlussklemmen (16)
gemäß des auf S. 10 abgebildeten
Schaltplanes an. Das Gerät ist an den
Schutzleiter anzuschließen.
4. Ziehen Sie die Schutztülle so weit
über die Anschlusskabel, dass die
Schutztülle einwandfrei in die
Aussparung der Zwischenwand passt.
Achten Sie dabei auf die Ausrichtung
der Schutztülle entsprechend der
Abbildung. Klappen Sie den Klapp -
halter zurück und rasten Sie ihn auf
der Heizpatrone ein.
5. Setzen Sie das Gehäuse auf das Gerät
und drehen Sie die Befestigungs-
schraube ein. Danach können Sie die
Blende aufrasten.
Hinweis:
Bei Bedarf kann die Anschlussklemme
(16) in den oberen Gerätebereich verlegt
werden. Bitte folgen Sie hierzu den
Anweisungen im nächsten Abschnitt.
release the keys. Operating mode 1 must
be selected first, thus to check the correct
operation of the load shedding relay at
low appliance output (35 degree setpoint
and low water flow rate). Mode 2 must
be selected if the load shedding relay
flickers.
Electrical connection
from below
1. Strip approximately 6 cm off the
connecting cable above the wall outlet.
With the smaller opening ahead, slide
the water splash protection sleeve
(22) over the connecting cable so
that the sleeve is flush with the wall.
This prevents any leak ing water from
coming into contact with the electrical
leads. It must not become damaged!
The protection sleeve must be used!
2. Open the control panel (15) rightwards.
3. Insulate the cables and plug them in
the connecting terminals (16) according
to the wiring diagram on page 10.
The appliance must be earthed.
4. Pull the protective sleeve over the
connecting cables until the sleeve
fits perfectly in the recess of the
intermediate panel. Adjust the water
splash protection sleeve as illustrated.
Reinsert the front part of the inter-
mediate panel. Reinsert the control
panel and lock it on the the heating
element.
5. Place the hood on the appliance and
screw in the fastening screw. After that
you can reinsert the faceplate.
Note:
If necessary, the connecting terminal (16)
can be displaced to the upper part of the
appliance. If you want to do so, please
follow the instructions in the next chapter.
22 16 15
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clage DEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clage DEX in the language / languages: English, German as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info