519304
10
Zoom out
Zoom in
Previous page
1/24
Next page
DEX
9 Elektroanschluss
(nurdurchdenFachmann)
Electrical connection
(onlybyaspecialist)
Zu beachten sind:
•VDE0100
•EN806-2
•Bestimmungenderörtlichen
Energie- und Wasserversorgungs-
unternehmen
•AngabenTypenschild
•TechnischeDaten:Seite5
•GerätanSchutzleiteranschließen!
BaulicheVoraussetzungen
•DasGerätmussdauerhaftanfest
verlegte Leitungen angeschlossen
werden. Das Gerät muss an den
Schutzleiter angeschlossen werden.
Kabelquerschnitt maximal 10mm
2
.
•DieElektroleitungenmüssensichin
einem einwandfreien Zustand befinden
und dürfen nach der Montage nicht
mehr berührbar sein.
•Installationsseitigisteineallpolige
Trennvorrichtung mit einer Kontakt-
öffnungsweite von mindestens
3 mm pro Pol vorzusehen (z.B. über
Sicherungen).
•ZurAbsicherungdesGerätesistein
Sicherungselement für Leitungsschutz
mit einem dem Gerätenennstrom
an-gepassten Auslösestrom zu
montieren.
Lastabwurfrelais
Beim Anschluss weiterer Drehstrom-
geräte kann ein Last abwurfrelais (82250)
an den Außenleiter L
2
angeschlossen
werden. Dazu muss am Gerät eine
besondere Betriebsart gewählt werden.
Drücken Sie zum
Ändern der Betriebsart
gleichzeitig alle vier Tasten
( , , und
) und warten, bis der
1 Elektronik / Electronic circuitry
2 Heizelement / Heating element
3 Sicherheitsdruckbegrenzer und
Sicherheitstemperatur begrenzer /
Safety pressure limiter and Safety
thermal cut-out
4 Klemmleiste / Terminal strip
Schaltplan / Wiring diagram
Please observe:
•Theinstallationmustcomply
with current IEC or national local
regulations and any particular
regulations, specified by the local
electricity supply company
•Observetheratingplateand
technical specifications on page 5
•Theunitmustbeearthed!
Structural prerequisites
•Theappliancemustbeinstalledviaa
permanent connection. Heater must
be earthed! A maximum cable size of
10 mm
2
must be observed.
•Theelectricwiringshouldnotbe
injured. After mounting, the wiring must
not be direct accessible.
•Anall-poledisconnectingdevice(e.g.
via fuses) with a contact opening width
of at least 3 mm per pole should be
provided at the installation end.
•Toprotecttheappliance,afuseelement
must be fitted with a tripping current
commensurate with the nominal current
of the appliance.
Load shedding relay
If further three-phase appliances are
connected, a load shedding relay
(82250)
can be connected to phase conductor
L
2
.
A special operating mode must be selec-
ted on the appli ance for this purpose.
To change the operating mode, press the
four keys ( , , and
) simul-
taneously and wait until the desired mode
(0, 1 or 2) is shown on the display, then
1
3
4
2
LCD Beschreibung
0
NormalerBetrieb,
Werkeinstellung
1
Betrieb mit normalem
Lastabwurfrelais
2
Betrieb mit empfindlichem
Lastabwurfrelais
LCD Description
0
Normaloperation,
manufacturer‘s setting
1
Operation with normal
load shedding relay
2
Operation with sensitive
load shedding relay
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clage DEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clage DEX in the language / languages: English, German as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info