519304
14
Zoom out
Zoom in
Previous page
1/24
Next page
DEX
10 Erstinbetriebnahme Initial operation
7.NachdemEinstellendermaximalen
Geräteleistung wird die Wasser heiz-
ung nach ca. 30 Sekunden Wasser fluss
aktiviert.
8.ÖffnenSiedasWarmwasserzapfventil.
Überprüfen Sie die Funktion des Durch-
lauferhitzers.
9. Machen Sie den Benutzer mit dem
Gebrauch vertraut und übergeben Sie
ihm die Gebrauchsanleitung.
10.Füllen Sie die Registrierkarte aus
und senden diese an den Zentral-
kundendienst oder registrieren Sie Ihr
Gerät online auf unserer Homepage
www.clage.de.
Hinweis »Erneute Inbetriebnahme«
Wird das Gerät nach der Erstinstallation
unter einer anderen Installations umge-
bung abermals in Betrieb genommen, so
kann es not wendig werden, die maxi male
Geräte leistung zu ändern. Durch kurz-
zeitiges Überbrücken der beiden Stifte
(siehe Bild) z.B. mit einem isolier ten
Schraubendreher(EN60900)gehtdas
Gerät in den Ausliefer zustand zurück. Alle
Parameter werden auf Werk ein stellung
gesetzt und die Heizung wird gesperrt. In
der Anzeige blinkt »21«, bis die maximale
Geräte leistung eingestellt wurde. Dieser
Zustand bleibt beim Aus- und Ein schalten
der Versorgungs span nung erhalten.
Sperr-Level
Der Umfang der Bedienung des Gerätes
kann einge schränkt werden.
Aktivierung der Sperrfunktion:
1.GerätvomNetztrennen(z.B.durch
Ausschalten der Sicherungen)
2. Brücke auf die Leistungselektronik
aufstecken (siehe Bild)
3. Gerät wieder in Betrieb nehmen
Deaktivieren der Sperrfunktion:
1.GerätvomNetztrennen
(Sicherungen ausschalten)
2. Brücke entfernen
3. Gerät wieder in Betrieb nehmen.
7. After having set the maximum
allowable power rating, the heating
element will be activated after
approx. 30 sec of water flow.
8. Open the hot water tap.
Check the function of the appliance.
9. Explain the user how the instantaneous
water heater works and hand over the
operating instructions.
10. Fill in the guarantee registration
card and send it to the CLAGE
Central Customer Service or use the
online registration on our website
www.clage.com.
Note „Reinstallation“
In case the appliance will be commis-
sioned again under different installation
conditions than during its initial ope-
ration, it may be necessary to adapt the
maximum power rating.
A temporary short-circuit of the two
pins,e.g.withascrewdriveracc.toEN
60900 (see figure), will reset all heater
para meters to works setting and lock the
heating. Value „21“ flashes in the display
until the maximum power rating has been
selected. This condition will maintain
when activating and deactivating the
supply voltage.
Lock level
The operating mode of the appliance can
be restricted.
Activation of the Lock level:
1. Disconnect the appliance from the
power supply (e.g. by switching off
the fuses)
2. Insert the jumper on the power
electronics (see picture)
3. Put the appliance into operation again
Deactivation of the Lock level:
1. Disconnect the appliance from the
power supply (e.g. by switching
off the fuses)
2. Remove jumper
3. Put the appliance into operation again
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clage DEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clage DEX in the language / languages: English, German as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info