Manual Casio QW3475 - GBD-H1000 G-SQUAD (page 24 of 58) (English)

740165

Zoom out

Zoom in

1/58

Note

●

Pressing (C) (step 3 of this procedure)

before the [GPS CAPTURE] message

appears causes run timing to start

using the watch’s accelerometer. Note

that your route is not recorded during

run timing using the accelerometer.

If you want your route to be recorded,

make sure that the [GPS CAPTURE]

message is displayed before you start

run timing.

●

It can take from about 30 seconds to

two minutes after you press (C) in step

2 for run timing using GPS to become

enabled. Under some signal reception

conditions, it may take as long as five

minutes.

Enabling run timing using GPS will

automatically cause the Training Mode

screen to appear.

Training Mode

3. Press (C).

Start run timing.

Note

●

The screen shown in step 2 of the

above procedure will not appear if the

Airplane Mode is enabled or if the GPS

setting is off.

●

You can find out the current GPS status

by checking whether or not the

mark on the display is flashing.

Not flashing: GPS enabled

Flashing: GPS disabled (Watch is

searching for GPS signals.)

●

After [GPS CAPTURE] appears and

is on the display, it means that the

GPS signal was lost and the watch is

searching for a signal.

●

If, while run time is being performed,

starts flashing on the display or

appears on the display, it means that

the watch is performing measurement

using its accelerometer and that your

route is not being recorded.

●

Entering the settings of the Compass,

Altimeter, Barometer, or Temperature

Mode during training will cause run

timing using GPS to stop momentarily.

The watch will start searching for GPS

signals again when you exit the setting.

If you want to use GPS for your run

timing, wait until [GPS CAPTURE]

appears on the display before you

start.

●

Pausing Run Timing

1. While the run timing screen is displayed,

press (C).

This pauses run timing and displays the

pause menu screen.

Pause Pause menu

2. Use (A) and (D) to select what you want to

do with the run timing data you have just

measured.

[RESUME] Resumes timing.

[SAVE] Saves data.

[DELETE] Deletes data.

3. Press (C).

●

If you select the data save option, the

run timing result screen will appear.

Pressing any button returns to the

Timekeeping Mode.

●

If you select the data delete option, the

watch returns to the Timekeeping

Mode.

●

Measuring Lap Times

Start run timing.

Starting Run Timing

2. Press (E).

Each press of (E) displays the elapsed

time of the current section or lap (lap time)

to appear.

Split time, lap distance

Lap time

Heart rate (average, maximum)

3. Press (A) or (D) to return to the run timing

screen.

●

If you do not perform any button

operation, the watch will return to the

run timing screen automatically after

about 10 seconds.

Note

●

You can change the lap time display

using G-SHOCK MOVE. Each of the

screens displays the items below.

ー　

Heart rate [AVG] (average), lap time,

[SPLIT TIME] (split time)

ー　

Heart rate [MAX] (maximum), lap

time, [DISTANCE] (lap distance)

Changing Display

Information During Run

Timing

One of three screens can be displayed during

run timing (Training Mode), and you can

specify the items you want to appear on each

screen.

This means you can configure a screen with

the items you want to monitor and display that

screen while you train.

Specifying the Screen to be Displayed

During Running (RUN FACE)

You can navigate between display screens by

pressing (A).

Example:

Changing the GPS Receive

Interval

Use the procedure below to specify the

interval for receiving GPS signals to acquire

location information while running.

1. Enter the Timekeeping Mode.

Navigating Between Modes

2. Press (C).

This displays the GPS signal receive start

screen.

3. Press (A) or (D).

This displays the Training Mode screen.

4. Hold down (A) for at least two seconds.

This displays the Training Mode setting

screen.

Pointer

Operation Guide 3475

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio QW3475 - GBD-H1000 G-SQUAD in the language / languages: English as an attachment in your email.

The manual is 4,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio QW3475 - GBD-H1000 G-SQUAD Manual

Product: