Manual Brother Innov-is M280D (page 87 of 100) (English)

718769

87

Zoom out

Zoom in

Previous page

1/100

Next page

Troubleshooting

85

APPENDIX

5

List of symptoms

Check the following possible problems before requesting

service. If the reference page is “*”, contact your authorized

Brother dealer or the nearest Brother authorized service

center.

■ Getting ready

■ While sewing

Symptom, Cause/solution

Reference

Cannot thread the needle.

Needle is not in the correct position.

• Press the “Needle position” button to raise the

needle.

6

Needle is installed incorrectly. 22

Needle is turned, bent or the point is dull. 22

Upper threading is incorrect.

The needle threader lever is not lowered until it

clicks.

17

The needle threader hook is bent and does not

pass through the eye of the needle.

*

The needle threader lever cannot be moved or

returned to its original position.

*

A size 65/9 needle is being used.

• The needle is incompatible with the needle

threader. Manually pass the thread through the

eye of the needle.

19

Bobbin thread does not wind neatly on the bobbin.

The thread is not passed through the bobbin

winding thread guide correctly.

13

The thread that was pulled out from the bobbin-

winding thread guide was incorrectly wound onto

the bobbin.

15

The empty bobbin was not set on the pin

properly.

13

While winding the bobbin, the bobbin thread was

wound below the bobbin winder seat.

The thread was incorrectly passed under the

pretension disk on the bobbin-winding thread

guide.

• Remove any entangled thread, and then wind

the bobbin.

13, 84

The bobbin thread cannot be pulled up.

Needle is turned, bent or the point is dull. 22

Bobbin is set incorrectly. 16

Nothing appears in the LCD.

Main power switch is not turned on. 9

The plug of the power cord is not inserted into an

electrical outlet.

9

The LCD screen is fogged up.

Condensation has formed on the LCD screen.

• After a while, the cloudiness will disappear.

–

The operation keys do not respond, or the key

response is too sensitive.

A glove is worn when the keys are pressed.

The keys are pressed with a fingernail.

A non-electrostatic touch pen is being used.

The sensitivity of the operation keys is not set for

the user.

6, 13

The sewing light does not come on.

[Light] is set to [OFF] in the settings screen. 12

Embroidery unit does not operate.

Embroidery unit is not attached correctly. 60

Symptom, Cause/solution

Reference

Machine does not operate.

“Start/Stop” button was not pressed. 25

The bobbin winder shaft is pushed to the right. 13

There is no stitch selected. 25

Presser foot is not lowered. 26

“Start/Stop” button was pressed with the foot

controller attached.

26

The “Start/Stop” button was pressed while the

machine is set for the sewing speed controller to

control the zigzag stitch width.

12, 49

Needle breaks.

Needle is installed incorrectly. 22

Needle clamp screw is not tightened. 22

Needle is turned or bent. 22

Using improper needle or thread for the selected

fabric.

21

Wrong presser foot was used. 23

Upper thread tension is too tight. 29

Fabric is pulled during sewing. –

Spool of thread is set incorrectly. 13

Symptom, Cause/solution

Reference

1

bonjour
je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03
Reply Report abuse
bonjour
je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
Merci bonne journée Submitted on 3-9-2022 at 10:38
Reply Report abuse
message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Brother Innov-is M280D at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info