718769

Brother Innov-is M280D Manual

85
Zoom out
Zoom in
Previous page
1/100
Next page
Troubleshooting
83
APPENDIX
5
i
Use the cleaning brush or a vacuum cleaner mini
attachment to remove any lint or dust from the race
and its surrounding area.
j
Use the included disc-shaped screwdriver to loosen the
two screws on the needle plate.
k
Slightly lift up the needle plate, cut any tangled
threads, and then remove the needle plate.
Remove the fabric and threads from the needle plate.
If the fabric cannot be removed, even after completing
these steps, contact your nearest Brother authorized
service center.
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the disc-shaped screwdriver to
firmly tighten the screw on the left side. Finally, firmly
tighten the screw on the right side.
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
p
Insert the bobbin case by following step k in
“Cleaning the race” on page 79.
q
Attach the needle plate cover according to step l in
“Cleaning the race” on page 79.
r
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
• Refer to “Checking the needle” on page 22 and
“Replacing the needle” on page 22.
■ Checking machine operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select stitch .
1 Cleaning brush
2 Race
If the fabric could be removed. Continue with step p.
If the fabric could not be removed. Continue with step j.
Note
• Compressed can air is not recommended to be used.
Note
• Be careful not to drop the removed screws in the
machine.
a
b
Memo
• Since the needle may have been damaged when the
fabric was caught in the machine, we recommend
replacing it with a new one.
Note
• Do not yet install the presser foot and thread.
a
b
… 85 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-m280d

Reset search

  • bonjour
    je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03

    Reply Report abuse

  • bonjour
    je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
    Merci bonne journée Submitted on 3-9-2022 at 10:38

    Reply Report abuse

  • message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is M280D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info