718769

Brother Innov-is M280D Manual

86
Zoom out
Zoom in
Previous page
1/100
Next page
Troubleshooting
84
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the fabric from the machine” on
page 82.
d
Select stitch . At this time, increase the stitch length
and width to their maximum settings.
• For details on changing the settings, refer to “Setting
the stitch width” on page 29 and “Setting the stitch
length” on page 29.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
If the needle or feed dogs contact the needle plate, the
machine may be malfunctioning; therefore, contact
your nearest Brother authorized service center.
f
Turn off the machine, and then install the bobbin and
presser foot.
Never use a scratched or damaged presser foot.
Otherwise, the needle may break, or sewing
performance may suffer.
• Refer to “Installing the bobbin” on page 16 and
“Replacing the presser foot” on page 23.
g
Correctly thread the machine.
• For details on threading the machine, refer to “Upper
Threading” on page 17.
h
Perform trial sewing with cotton fabric.
If the thread becomes tangled under the
bobbin winder seat
If the bobbin winding starts when the thread is not passed
under the pretension disk of the bobbin-winding thread guide
correctly, the thread may become tangled under the bobbin
winder seat.
a
Stop the bobbin winding.
b
Cut the thread with scissors beside the bobbin-winding
thread guide.
c
Slide the bobbin winder shaft to the left, and then
remove the bobbin from the shaft and cut the thread
leading to the bobbin in order to be able to completely
remove the bobbin from shaft.
d
Hold the thread end with your left hand, and wind off
the thread clockwise from under the bobbin winder
seat with your right hand as shown below.
1 Opening in the needle
plate
2 Handwheel
Note
• Incorrect sewing may be the result of incorrect upper
threading or sewing thin fabrics. If there are poor results
from the trial sewing, check the upper threading or the
type of fabric being used.
a
b
CAUTION
• Do not remove the bobbin winder seat even if
the thread become tangled under the bobbin
winder seat. Otherwise, the cutter in the
bobbin winder seat may be damaged.
• Do not remove the screw on the bobbin
winder guide post, otherwise the machine may
be damaged; you cannot wind off the thread
by removing the screw.
1 Screw of the bobbin winder guide post
a
… 86 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-m280d

Reset search

  • bonjour
    je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03

    Reply Report abuse

  • bonjour
    je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
    Merci bonne journée Submitted on 3-9-2022 at 10:38

    Reply Report abuse

  • message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is M280D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info