79055
21
Zoom out
Zoom in
Previous page
1/135
Next page
English - 7
Flap Disc
For operations with the rubber sanding
plate/the cup brush/the wheel brush /the flap
disc, always mount the hand guard (acces-
sory).
Position the flap disc on the grinder spindle 6.
Screw on the quick-clamping nut 11 and tighten
the flap disc.
Rubber Sanding Plate 19
For operations with the rubber sanding
plate/the cup brush/the wheel brush /the flap
disc, always mount the hand guard (acces-
sory).
For mounting, see the illustration page.
Screw on the round nut 21 and tighten with the
two-pin spanner.
Increased effort must be taken into account when
loosening the round nut 21.
Cup Brush 22/Disc Brush
For operations with the rubber sanding
plate/the cup brush/the wheel brush /the flap
disc, always mount the hand guard (acces-
sory).
The grinding tool must be able to be screwed
onto the grinding spindle 6 until it rests firmly
against the grinder spindle flange at the end of
the grinder spindle threads. Tighten with an
open-end spanner.
Increased effort must be taken into account when
loosening the grinding tool.
Grinding Cup
When working with grinding cups, use
the special guard 14.
The grinding cup 15 should always protrude
from the guard 14 only as far as absolutely nec-
essary for the work to be performed in each case.
Adjust the guard 14 to this distance.
For mounting, see the illustration page.
Screw the clamping nut 16 on to the grinder spin-
dle 6 ensuring that the flat side faces the grinding
disc and tighten the clamping nut with the fitting
offset two-pin spanner 17.
Increased effort must be taken into account when
loosening the clamping nut 16.
All grinding tools mentioned in these operating in-
structions can be used.
The permissible speed [rpm] or the circumferen-
tial speed [m/s] of the grinding tools used must at
least match the values given in the table.
Therefore, always observe the permissible
rotational/circumferential speed on the label
of the grinding tool.
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
To start the machine, press the On/Off switch 3
forward and then down.
To lock-on, push the pressed On/Off switch 3
further forwards.
To switch off the machine, release the On/Off
switch 3 or push and release it then.
Switch version without lock
(country-specific):
To start the machine, press the On/Off switch 3
forward and then down.
To switch off the machine, release the On/Off
switch 3.
Approved Grinding Tools
max.
[mm] [mm]
Db d[rpm] [m/s]
180
230
8
8
22.2
22.2
8 500
6 500
80
80
180
230
8 500
6 500
80
80
100 30 M 14 8 500 45
Starting Operation
b
d
D
D
D
b
d
1 609 929 H82.book Seite 7 Dienstag, 3. Mai 2005 3:11 15
22 1 609 929 H82 TMS 28.04.05
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 24-230 JBX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 24-230 JBX in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info