79055
22
Zoom out
Zoom in
Previous page
1/135
Next page
English - 8
Test run!
Check the grinding tool before use. The
grinding tool must be properly mounted
and rotate freely. Perform a test run of at
least 30 seconds without load. Do not use
damaged, out-of-round or vibrating grind-
ing tools.
Run-on Brake
This machine is equipped with the
Bosch Brake System, a patented
electro-mechanical run-on brake.
When switching off or in case of a power supply
interruption, the grinding tool is stopped within a
few seconds. This means the run-on time is re-
duced by approx. 70 % in comparison to angle
grinders without run-on brake, and that the ma-
chine can be placed down in shorter time.
Should the braking effect of the run-on brake no-
ticeably diminish, have the machine checked by
an after-sales service centre for Bosch power
tools.
Reduced Starting Current
(GWS 24-180 JBX/GWS 24-230 JBX)
As a result of soft starting, a 13 A fuse is ade-
quate.
A machine without reduced starting current
requires higher fuse protection (use at least
a 13 A time-delay fuse).
Exercise caution when cutting slots in
structural walls: See Information on Struc-
tures.
Clamp the workpiece if it does not remain sta-
tionary due to its own weight.
Do not strain the machine so heavily that it
comes to a standstill.
Grinding and cutting discs become very hot
while working; do not touch until they have
cooled.
Rough Grinding
The best roughing results are
achieved when setting the machine
at an angle of 30° to 40°. Move the
machine back and forth with mod-
erate pressure. In this manner, the
workpiece will not become too hot,
does not discolour and no grooves
are formed.
Never use a cutting disc for roughing.
Flap Disc
With the flap disc (accessory), curved surfaces
and profiles (contour sanding) can be worked.
Flap discs have a considerably higher service life
than sanding sheets, lower noise level and lower
sanding temperatures.
Cutting
When cutting, do not press, tilt or
oscillate the machine. Work with
moderate feed, adapted to the ma-
terial being cut.
Do not reduce the speed of running down cutting
discs by applying sideward pressure.
The direction in
which the cutting is
performed is impor-
tant.
The machine must
always work in an
up-grinding motion.
Therefore, never
move the machine in
the other direction!
Otherwise, the dan-
ger exists of it being
pushed uncon-
trolled out of the cut.
Operating Instructions
1 609 929 H82.book Seite 8 Dienstag, 3. Mai 2005 3:11 15
23 1 609 929 H82 TMS 28.04.05
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 24-230 JBX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 24-230 JBX in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info