697457
146
Zoom out
Zoom in
Previous page
1/158
Next page
RF Keyfob Battery Failure
Condition:
The Keyfob has experienced a low battery condition, if wireless module is enabled.
Restore:
The Keyfob battery restored and fault is reset.
Supervise:
1. 1. Report the Keyfob battery fault to configured destination when the fault is detected.
2. Slow flash FAULT indicator (refer to Keypad Indicators for the detailed description).
3. When the fault is reset, send the restored report to the configured destinations. The
FAULT indicator is turned off when there is no other system fault.
3 -Output Failure
Onboard Output Failure
On-board output 1 to 2 fault
The on-board output 1 to 2 is detected as short circuit, open circuit, or over current status,
the on-board output 1 to 2 fault will occur. After the output is recovered and reset command
executed, the fault will be recovered.
Fault conditions:
When the output is at short circuit, open circuit, or over current status, the fault occurs.
Recovery conditions:
After the output is recovered, the fault will be recovered.
Fault monitoring:
1. The on-board output 1 to 2 fault is detected, the report will be sent to the relevant path.
2. The fault indicator on the keypad flashes slowly.
3. When the on-board output 1 to 2 fault recovers, the report will be sent to the specified
path. If currently there are not other faults and reset command executed, the fault
indicator of the keypad will go off.
4 -Keypad Failure
Condition:
Keypad fail is reported at any time when communication fails between the panel and address
1 keypad.
Restore:
Communication between panel and keypads comes back to normal, and fault is reset.
Supervise:
1. Report the keypad fault to the configured destination programmed on address 124.
2. Flash FAULT indicator on the other keypad in normal operation (refer to Keypad
Indicators for the detailed description).
3. Keypad missing communication with the panel performance as below:
Stop detection on the keypad button
Flash FAULT indicator
The disconnected keypad do not sound FAULT beeping per minute
4. When the keypad fault is reset, send the restore report to the configured destinations.
The FAULT indicator is turned off when there is no other system fault.
5- System Failure
Date and Time not set
Condition:
Date and time is not set after the system is powered on.
Restore:
146
en | Troubleshooting AMAX 2100 / 3000 / 4000
2013.10 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
146


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AMAX 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AMAX 4000 in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AMAX 4000

Bosch AMAX 4000 User Manual - English - 24 pages

Bosch AMAX 4000 User Manual - English - 36 pages

Bosch AMAX 4000 Quick start guide - English - 38 pages

Bosch AMAX 4000 Installation Guide - German - 170 pages

Bosch AMAX 4000 Quick start guide - German - 34 pages

Bosch AMAX 4000 Installation Guide - Dutch - 166 pages

Bosch AMAX 4000 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info