Manual Bomann NM 6063 CB (page 14 of 74) (English, German, Dutch, French, Italian, Polish, Spanish)

814761

Zoom out

Zoom in

1/74

NM6063CB_IM 19.04.23

6. Continue to guide the thread down

and pass it through the hole on the

needle clamp.

7. Finally, pull the thread through

the needle hole. Let the thread

run to the back under the presser

foot (20). Make sure you pull the

thread about 10 cm behind the

presser foot.

Adjusting the Upper-thread Tension

The setting is made by turning the adjusting wheel (2).

The basic setting is between 4 and 5.

Depending on the fabric and yarn thickness, turn the

adjusting wheel so that the knotting of the upper and lower

threads is visible as a dot on the top of the fabric. If loops

form, the thread tension is too loose.

Winding the Under-thread Bobbin

CAUTION:

Remove the upper thread completely from the sewing

machine. Otherwise it will wrap around internal compo-

nents and the sewing machine will block.

1. Place a thread spool on the thread spool holder (15).

2. Put an empty under-thread bobbin (27) on the bobbin

winder (14).

3. Guide the thread through the thread guide (16) to the

empty bobbin.

4. Wind the thread clockwise a few times around the empty

bobbin.

5. Push the bobbin against the bobbin

winder stop (13) (see illustration).

6. Start winding with the foot pedal

(25) or use the switch (8).

7. When the winder is full, the winding

stops automatically. If you want to

stop winding prematurely, release

the foot pedal.

8. Cut the thread and remove the bobbin.

Inserting the Under-thread Bobbin

1. The needle must be fully raised when inserting or remov-

ing the under-thread bobbin (27). Turn the handwheel (6)

in the direction of the arrow.

2. Pull the bobbin cover (10) off to the front.

3. Place the bobbin in the hook so that

it turns anticlockwise (see illustra-

tion). Let the thread hang out of the

bobbin by about 10 cm.

4. Push the bobbin cover back in.

Bringing up the Under-thread

1. Raise the presser foot (20).

2. Hold the upper-thread with your left hand.

3. At the same time, with your right hand, turn the

handwheel (6) in the direction of the arrow until the nee-

dle is raised (one complete turn of the handwheel).

4. Pull the lower and upper-threads 10 cm back under the

presser foot. You can use a scissor or the thread cutter

(12) for this.

Select Stitch Pattern

There are 12 stitch pattern types to choose from.

Select a stitch pattern using the table below. When turning

the stitch pattern adjusting wheel (3), the needle must

always be in the uppermost position.

Stitch

Pattern Explanation

1Straight stitch, small stitch length

2Straight stitch, medium stitch length

3Straight stitch, long stitch length

4Straight stitch, needle left, medium stitch length

5Elastic stitch

6Blind stitch

7Buttonhole

8Buttonhole

9Wide zigzag stitch, small stitch length

10 Narrow zigzag stitch, medium stitch length

11 Wide zigzag stitch, medium stitch length

12 Wide zigzag stitch, long stitch length

1. The needle must be completely raised. Turn the

handwheel (6) in the direction of the arrow.

2. Set the stitch pattern adjusting wheel to the desired

setting. Make sure that the stitch pattern adjusting wheel

locks in the desired position.

Sewing

1. Make sure that the winder (14) is in the left position.

2. Raise the presser foot (20). Make sure that the upper-

thread and under-thread is pulled back about 10 cm.

3. Place the fabric under the presser foot and lower the

presser foot.

4. Start sewing. Slowly press the foot pedal (25) or select

one of the two speed levels with the switch (8). Guide the

fabric with your hand.

- IMPORTANT! Do not pull or push the fabric while

sewing. This can cause damage to the needle!

5. To sew a bartack at the end of the seam or in the seam,

press down the button to sew backwards (7). When the

button is released, the sewing machine sews forward

again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann NM 6063 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann NM 6063 CB Manual

Product: