814761
13
Zoom out
Zoom in
Previous page
1/74
Next page
NM6063CB_IM 19.04.23
13
Selection of Needle Size and Threads
Needle system: System 130 at-shank needle
Needle
Size Fabrics Thread
80
(12)
Medium weight
fabrics: Cotton, satin,
workwear, canvas,
double-faced fabrics,
lightweight wool
Most threads are of
medium size and
suitable for these
fabrics and needle
sizes.
For best results:
use polyester
threads for syn-
thetics and cotton
or naturally woven
fabrics. Always use
the same thread at
the top and bottom.
90
(14)
Medium weight
fabrics: Wool, heavier
knitwear, terry cloth,
denim fabrics
100
(16)
Heavy fabrics: Wool,
tent fabrics and quilted
fabrics, denim, uphol-
stery fabrics (light to
medium)
110
(18)
Heavy fabrics: Wool,
coat fabrics, upholstery
fabrics, some leather
and vinyl (with leather
needles)
Durable thread
Operation
Inserting the Needle
WARNING: Risk of Injury!
Before inserting or replacing the needle, unplug the
power supply unit from the sewing machine.
Change the needle regularly, especially if it is bent or the
tip is damaged. A bent needle causes skipped stitches.
Defective needle tips damage the fabric.
Insert the needle as follows:
1. The needle guide must be com-
pletely raised. Turn the handwheel
(6) in the direction of the arrow.
2. Loosen the needle clamp screw
(21) and remove the old needle.
3. Insert the new needle as far as it
will go. The at side of the needle
must face backwards.
4. Tighten the needle clamp screw again.
Attaching and Removing the Presser Foot
There are different types of presser feet. You can buy them
in shops. Make sure you get the right size. Not all presser
feet t every sewing machine.
To change or remove the presser foot, refer to the following
description with the illustrations 13.
1. Illustration 1:
Pull the presser foot lever (17) up. Loosen the presser foot
xing screw (a). Place the presser foot holder (b) on the
presser foot bar (c) and tighten the screw (a).
2. Illustration
2:
Place the presser foot (d) on the needle plate. Lower the
presser foot lever (17) until the notch (e) is exactly over
the presser foot pin (f). Press the lever (g) until the pin (f)
engages in the notch (e).
3. Illustration
3:
To remove the presser foot (20), press lever (g). The
presser foot falls off.
Threading the Upper-thread
For threading the upper-thread, refer to the illustrations
below. Also refer to the illustrated instructions on the
appliance.
When threading, make sure that the presser foot (20) is
raised and the thread lever (1) is in the uppermost position!
1. Place the thread spool on the
thread spool holder (15).
2. Pull the thread through the thread
guide (16).
3. Guide the thread down past the
adjusting wheel (2).
4. When you reach the bottom, guide
it up the left side to the thread
lever (1).
5. Guide the thread through the hole
on the thread lever (1). Make sure
that the thread is inserted from
right to left.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann NM 6063 CB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann NM 6063 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info