693645
23
Zoom out
Zoom in
Previous page
1/32
Next page
starting any work on the boiler, check that it is disconnected from the electrical power (the
plug is pulled out of the socket).
8.) As the function of the ventilator can result in a slight overpressure in the burner area, keep in mind
that the boiler must be tightly closed (fire door, upper cover, cleaning gap of the feeder, container
cover etc.).
9.) If the boiler is equipped with the fire extinguisher with paraffin plug, make a visual check of the
emergency extinguishing system from time to time and refill water if necessary.
10.) If the boiler is equipped with the fire extinguishing system with the thermostatic valve and
pressure bottle, and if an emergency situation occurs (longer power failure etc.) and the fuel in the
fuel container starts burning, the increased temperature will cause the thermostatic valve to open
and the fire will be extinguished with water from the water supply system or from the installed water
pressure tank.
Before the boiler is put into operation again, it is necessary to remove wet fuel, fill the water pressure
bottle and heat the boiler as described in 7.1.
If the water pressure tank is a part of the emergency extinguishing system, the air pressure in the
tank must be checked at least once a year. To this end, remove the cap of the valve at the tank and
using a common manometer, check the pressure. If the pressure is not sufficient, adjust it to 0,5 bar
with an air pump or a compressor.
11.) The worm feeder drive gear and the turniket drive gear are filled with synthetic oil from the
production and further maintenance is not required.
9. Troubleshooting
If problems with operation of the boiler appear, try one of the following solutions:
SYMPTOM REASON SOLUTION
The boiler is not connected
to the network.
Connect the boiler to the electrical power
network (230V/50Hz) with appropriate
cable with plug.
The display shows no
data.
Malfunction of the boiler
controller.
Change the controller for a new one.*
The cable of the engine is
disconnected / damaged.
Connect the engine / change the cable to
the engine.*
The engine is damaged. Change the engine.*
The worm feeder
doesn’t work.
The engine was overheated
and the thermal protection
was activated.
Let the engine cool down, after cooling the
engine will start again.
The worm feeder is blocked
(stone, etc.)
Dismantle the worm feeder and remove
the problem. Re-assemble the device.*
The thermal
protection of the
engine was activated
repeatedly.
In the fuel there is a great
amount of dust.
Remove the inappropriate fuel from the
boiler; fill the container with the specified
fuel.
The boiler drive is
working, but the
worm feeder doesn’t
work
The elastic pin between the
worm feeder and the drive
rod was cut.
Remove the rest of the broken pin and
install a new one (8x45, ISO 8752).
The worm gear is
moving but the fuel is
not being transported
There is no fuel in the
container.
Fill the container with recommended fuel.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benekov R100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benekov R100 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info