519289

Atika BMS250 Manual

23
Zoom out
Zoom in
Previous page
1/101
Next page
On / Off Switch
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switch on
Press the green button ( I )
on the switch.
L
If there is a power cut, the
machine switches off
automatically. To switch on
again, press the green ( I )
button.
Switch off
Press the red button ( 0 ) on the switch.
Motor protection
The motor is equipped with a safety switch and
switches off independently when overloaded.
It can be switched back on following cooling phase (5 -
10 min.) .
First press
1. the red button (0)
2. the small button with the clear cover (15)
3. the green button ( I ) to start
Dust/chip exhaustion
The wood dust generated during operation impedes the
necessary view and is harmful to health to some degree.
If the machine is not used in the open air, a shavings exhausts
must be attached to both exhaust outlets (e.g. small
transportable dust remover).
Chip exhaustion
Connect a chip exhaust system or small vacuum cleaner
with suitable adapter to the chip exhaust neck (26) (Ø 35 mm).
L Air velocity at the exhaust neck of the saw ≥ 20 m/sec
Use a special exhaust device when exhausting dusts that are
especially harmful to health, carcinogen or dry.
22
Adjusting the saw
Pull the mains plug before performing
settings.
Splitting wedge setting
The splitting wedge is an important safety device as it prevents
the workpiece from recoiling
To guarantee the function of the splitting wedge, its distance
from the toothed wheel its distance from the teeth of the saw
blade above the table must not be more than 5 mm.
Set the cutting height
The cut height
can be adjusted
stepless from 0
- 75 mm using
the crank (11).
Before setting
the cut height,
tighten the set
screw for the
saw blade (13).
Set the cutting
height 5 mm
higher than the
material
thickness.
Adjust saw blade pitch
The saw blade must not be set to the inclined position
when the blade is turning. The motor must be switched
off first.
Adjusting between 0° - 45°
1. Loosen the
clamping screw
(13).
2. Turn the
handwheel until
the required angle
is shown (0° -
45°).
3. Retighten the set
screw.
Adjusting the angle indicator:
1. Turn the machine off and unplug the power cord.
2. Use an angle stop to align the saw blade vertically.
3. Loosen the screw (A) and slide the angle indicator to the 0°
mark.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BMS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BMS250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info