519289

Atika BMS250 Manual

21
Zoom out
Zoom in
Previous page
1/101
Next page
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
− Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
20
− Damaged or illegible security labels have to be
replaced.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and
adjusting tools are removed.
Store unused equipment in a dry, locked place out of the
reach of children.
Electrical safety
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-profile section of at least
− 1.5 mm2 for cable lengths up to 25m
− 2.5 mm2 for cable lengths over 25m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
Protect yourself against electric shocks. Avoid touching
earthed parts with your body.
The connector of the connection cable must be splash-
proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the saw cable and if damaged, have it
renewed by a recognised skilled electrician.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current
circuit breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts and accessorie parts.
Accidents can arise for the user through the use of other
spare parts. The manufacturer is not liable for any damage
or injury resulting from such action.
Assembly of the saw
A1 A2 A33
Unfold the stand (16).
1. Bring the frame stand together so that the lock is released.
2. Pull up the frame until it latches again.
B1 B2
Install the transport wheels (18).
C
Turn the saw around. You can align the saw by turning the
adjusting foot (17) in or out.
Install splitting wedge
D1
1. Turn the screw out.
2. Place the screwdriver in the hole to take out the table insert
(6).
D2
Raise the saw blade (22) to its highest position.
D3
Loosen the screw on the clamp.
D4
Insert the splitting wedge (23) between the pressure plate (33)
and the counter-plate (34).
D5
1. Adjust the splitting wedge (23). The distance between the
saw blade and splitting wedge must be max. 5 mm.
2. Retighten the screw on the clamp.
D6
1. Reinsert the table insert (6).
2. Stand behind the saw, insert the screwdriver in the hole and
pull it towards you so that the table insert latches in place.
3. Retighten the screw for attaching the table insert.
E
Attach the safety guard (5) using an M6 x 40 coach bolt and an
M6 wing nut on the splitting wedge (23).
F1 F2
Screw both holders (27 and 28) on.
Install bench length extension
G1
Attach the bench length extension (1) using the two hex head
screws M6 x 12.
G2 G3
Attach the supports (24) to the bench length extension (1) using
two hex head screws M6 x 12, washers A 6,4 and M6 hex nuts.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BMS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BMS250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info