519289

Atika BMS250 Manual

22
Zoom out
Zoom in
Previous page
1/101
Next page
21
G4
Attach the supports (24) to the housing using two self-tapping
screws.
Install bench width extension
H1
Remove the two self-tapping screws from the bench width
extension (21) with the rubber feet (20). The bench width
extension with rubber feet must be attached to the side with the
transport wheels.
H2
Loosen the two set screws (31).
H3
1. Slide the bench width extension with rubber feet just slightly
into the bench plate.
2. Turn the self-tapping screws back into the bars of the bench
width extension.
H4
Slide the bench width extension all the way into the bench plate
or as far as required for sawing and then retighten the two set
screws (31).
Now install the second bench plate (21A).
Plug the suction hose (4) onto its connection on the safety
guard (5) and on the housing (26).
J
Loosen the knurled nuts on the fence (3A) and place the fence
onto the fence holder (3B) and retighten the nuts.
K
Loosen the knurled nuts on the rip fence. Slide the fence (7A)
onto the holding plate (7B) and retighten the nuts.
Preparing for commissioning
L
To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the saw in a place that fulfils the following conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
Any unevenness of the floor can be compensated by
loosening the lock nut on the adjusting foot and turning the
adjusting foot (17) in or out until the saw is again steady. C
To guarantee even more secure placement when working
with the saw, the saw can be attached to the floor using two
angle brackets.
(extra accessory, angle bracket set Order No. 362510)
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− that the guard is in a proper condition
− the splitting wedge setting (see splitting wedge setting)
− that the table insert is in a proper condition
− whether the pushstick is to hand
− the saw blade for flawless condition
Do not use any cracked saw blades or such that have
changed their shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged table insert.
When sawing, place yourself to the side of the danger area
(saw blade).
Lower the guard onto the bench top
− when working on the workpiece
− when interrupting the work or leaving the saw
Commissioning
Rotational direction of the saw blade
L
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard (5).
Selection of saw blades
Consider when selecting the saw blade, that no edgeless or
damaged saw bands are used and that the diameter of the
blade location hole is 30 mm.
I
The saw blade supplied as a standard is suitable for timber and
most plastics.
Other saw blades are available for other uses on
request. Ask your dealer or us.
L Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug
L Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker (FI switch 30 mA).
L Main fuse: 16 A inert
Use the connection or extension cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm2 for cable lengths up to 25m
2.5 mm2 for cable lengths over 25m
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BMS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BMS250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info