519289

Atika BMS250 Manual

24
Zoom out
Zoom in
Previous page
1/101
Next page
Fitting and adjusting the transverse stop
The transverse stop supplied can be used as a
transverse or mitre stop.
L
Setting the angle. Loosen the clamping screw of the
transverse stop by turning.
Fit the transverse stop to the saw table plate
Push the transverse stop into one of the two grooves
on the saw table plate.
Setting the angle
Loosen the clamping screw of the transverse stop by
turning. You can now set the stop to the required angle.
Turn the clamping screw tight again.
23
Fitting and adjusting the longitudinal stop
Fit the longitudinal stop to the saw table plate.
The longitudinal stop (7) can be installed on the left or right of
the saw blade. To attach the fence (7A) on the other side of the
stop,
remove the fence,
unscrew the two knurled nuts,
attach the guide plate on the other side of the stop,
reinstall the fence.
L
Make sure that the fences are correctly adjusted. ( See "
Working instructions").
Setting the longitudinal stop
1. Place the longitudinal stop in the guide profile on the bench.
2. Set the desired dimension and turn the lever (8) down.
3. To obtain a precise cut, first make a test cut and then
readjust the stop as needed.
Working with the saw
Before starting to work consider the following safety advices to
keep the risk of injuries as small as possible.
Protective guard, splitting wedge and saw blade ok?
Place your hands flat on the workpiece with fingers closed.
Stoppers (fences) ready for use and pushstick to hand?
Workplace tidied?
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Before making adjustments to the saw settings (e.g. replacing
the saw blade etc.)
− switch off device
− Wait for standstill of the saw blade
− pull out main plug
Also, note the following important points:
Place yourself outside of the area of danger.
Place your hands flat on the workpiece with fingers closed.
With it, lead the work piece with the hand only up to the
leading edge of the saw blade protection.
Never remove loose splinters, chips, or similar by hand.
Ensure that you always comply with the safety
instructions given on p. 18.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BMS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BMS250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info