519289

Atika BMS250 Manual

25
Zoom out
Zoom in
Previous page
1/101
Next page
Cutting narrow workpieces
24
(Width less than 120 mm)
Push the workpiece forward with both hands, in the area
of the saw blade, use the pushstick (30).
When working on very flat and narrow workpieces
(Width 30 mm and less) use the lower guide are of the
fence (7A).
Cutting wide workpieces
With the flat of the hand and the fingers closed, push the
work piece to be cut along the stop.
Cross cuts / mitre cuts
Push the transverse stop (3) into one of the guide grooves
on the table and set the transverse stop to the required
angle.
Push the longitudinal stop (7) into the required position, so
that the work piece can be securely held in place.
Place the workpiece to be cut against the stop rails.
Hold the workpiece firmly in place and push it past the saw
blade using the transverse stop. Use the pushing bar if
necessary.
Maintenance and Care
Before each maintenance and cleaning
work
− switch off device
− wait for stop of chain saw
− pull out main plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
L Observe the following to maintain the functionality of the
saw.
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
L Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Take care that the saw blade remains free of rust and resin.
Remove all resin residues from the saw bench top
L Resin residues can be removed with a commercial
maintenance and care spray.
The saw blade is a wearing part and will become dull after
prolonged or frequent use.
renew the saw blade or have it sharpened
Maintenance
Changing the saw blade (p. 93 - p. 97)
Before replacing the saw blade remove the
plug from the mains.
Do not use any saw blades made of HSS steel.
Do not use any cracked saw blades or such that have
changed their shape.
Only use well-sharpened saw blades
Replacing the table insert
Immediately replace a worn or damaged table insert.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BMS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BMS250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info