736695

AS Motor AS 940 Sherpa 4 WD RC Manual

24
Zoom out
Zoom in
Previous page
1/60
Next page
Switching on receiver and transmitter
24
Adjusting the seat suspension
The seat suspension should be adjusted to the driver’s
weight and the terrain features. You will sit most comfortably
when the spring travel is fully made use of.
The seat suspension should be set as soft as possible to
keep it from going coil-bound during normal operation. You
can read the current setting from the scale on the seat.
If the seat goes coil-bound during normal operation, turn the
handwheel clockwise. The indicator moves towards 5. The
seat suspension becomes stiffer.
If the seat suspension is stiff during normal operation and
thus uncomfortable, turn the handwheel anticlockwise. The
indicator moves towards 1. The seat suspension becomes
softer.
Guide values for driver’s weight for flat terrain:
kg Scale
50 ≥ 2
90 ≥ 3
130 ≥ 4
Putting up the bar
For safety reasons, always use the device with the bar folded
up and locked. If the device tips over, the bar can prevent the
device from overturning. Serious damage to the device can
be thus avoided.
The device may only be used with the bar folded down on
level ground.
Transport rack
Warning
During the loading process, there is an increased risk of
tilting.
► Do not drive up or down steep slopes when the trans-
port rack is loaded. Observe the permissible loading
limits.
The device has a transport rack above the engine cover.
Warning
Risk of accident due to inaccessible control elements at
the rear end.
► Make sure that the Emergency stop and the selector
lever operating modes are always freely accessible.
Notice
There is a hazard due to incorrect loading that the engine
overheats and is damaged.
► Only load the transport rack so that the ventilation grid
that is located below it is not covered.
Loading limits
Maximum load: 5 kg
Maximum height: 18 cm
Maximum width: 45 cm
Maximum length: 30 cm
Switching on receiver and
transmitter
No matter in which operating mode you want to work, you
must switch on the receiver first.
1. Switch on the main switch on the device.
ð When the control has booted, the status indicators on
the device light up.
1
15
416
B
A
Fig.9:
2. Place the key (A) on the start-stop switch (B).
3. Turn the key(A) clockwise to switch on the transmitter.
4. Wait until the horn of the device sounds once.
ð In the display (16) the frequency number is briefly dis-
played.
ð The status indicators on the device and on the trans-
mitter (15) go out.
5. Press the button “Horn” (4) on the transmitter to get the
device ready for operation.
ð The horn signals that the device is ready for operation.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info