736695

AS Motor AS 940 Sherpa 4 WD RC Manual

25
Zoom out
Zoom in
Previous page
1/60
Next page
Working in the MC mode
25
Selecting radio frequency
When you switch on the transmitter, the receiver automatic-
ally searches a suitable frequency.
If several remote controlled devices are operated at the same
time or when another transmitter is located close by, faults in
the radio contact can occur. If this is the case, change the
frequency.
Changing the radio frequency
Fig.10:
1. Continue to press the button “Horn/acknowledge” (4).
2. Press the button “Display frequency” (11).
ð In the display (16) the frequency number is briefly dis-
played.
ð When the transmitter has set a new frequency, the horns
sounds and the device is ready for operation.
Working in the MC mode
Requirements
– The selection lever operating mode is set to MC mode.
– The transmitter is in the transmitter holder.
– There is a driver on the driver’s seat.
Starting the engine in the MC mode
Requirements
– The fuel valve is open.
– The tank ventilation is open.
– The drive lever on the device is in neutral position.
– Receiver and transmitter are switched on and ready for op-
eration.
Starting
Warning
During startup, there is a risk of injury due to rotating
blades.
► Make sure that nobody is in the danger area of the
blade.
Warning
Danger of poisoning due to poisonous exhaust gases.
► Do not operate the engine in closed or insufficiently
ventilated rooms.
► Please observe the safety instruction regarding the
poisoning risk.
Fig.11:
1. When the engine is warm:
Move the accelerator lever to middle position (full throttle).
When the engine and outside temperatures are cold
(cold start):
Move the accelerator lever to cold start position (Choke).
2. Press the key “Engine start” (5) on the transmitter.
ð Engine is started.
ð The oil control lamp (14) on the transmitter goes out.
3. Only after cold start:
Move the accelerator lever to middle position (full throttle).
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info