736695

AS Motor AS 940 Sherpa 4 WD RC Manual

23
Zoom out
Zoom in
Previous page
1/60
Next page
Prior to starting
23
Prior to starting
Checking the oil level
Notice
Incorrect oil level can damage the engine.
► Prior to each use, check the engine oil level and the oil
level in the hydrostat (see Maintenance).
Observe the information in the operator’s manual of the en-
gine manufacturer.
Fuel
As fuel, use unleaded petrol (see operating instructions of the
engine manufacturer).
You can use E10 petrol. Do not store E10 petrol longer than
30 days.
Tanking up
Warning
Fuel is ignited by hot engine parts.
► Prior to filling up, switch off the engine and wait for at
least 20minutes until the engine has cooled down. Ob-
serve the safety instructions regarding the fuel!
Filling up with fuel
1. For filling, use a canister with filler spout or a funnel.
2. Open the canister carefully so that existing excess pres-
sure is slowly reduced.
3. Open the tank cap carefully so that existing excess pres-
sure is slowly reduced and no fuel sprays out.
4. Fill the fuel tank.
5. Tightly close the tank cap again.
Checking and changing the battery of the
transmitter
When working, always carry an extra battery.
If the batteries in the transmitter are charged too low or the
batteries are unsuitable, these can be the consequences:
– The range of the radio contact drops.
– The radio contact becomes unreliable.
– An Emergency stop is triggered.
– The device cannot be operated any longer, also in the MC
mode.
Checking the battery
Fig.8:
1. Switch on the transmitter with the start-stop switch(1).
ð In the display(16) the frequency number is briefly
shown.
ð In the display(16) a dot jumps back and forth: The
battery is ok.
ð The display(16) flashes an “L”: Warning low battery
capacity. You can continue to operate the transmitter
for approx. 30 minutes.
Notice: If the batteries are unsuitable or faulty, this test can
produce an incorrect result. In that case, please replace the
batteries.
Changing the batteries
1. Move the device to a safe position and switch it off.
2. Loosen the locking screw at the battery compartment and
remove the cover.
3. Replace the batteries with 2 new batteries or 2 charged
batteries.
4. Close the cover and tighten the locking screw.
5. Switch on the transmitter via the start-stop switch.
6. Check if a dot is jumping on the display.
Adjusting the seating position
Adjust the seat in the longitudinal direction until your feet are
positioned on the inclined support plates and you sit comfort-
ably.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info