541367
14
Zoom out
Zoom in
Previous page
1/32
Next page
GLD User Guide 14 AP8561 iss.2
GLD-AR2412 Main AudioRack
Input sockets 24 balanced XLR inputs for
microphone and line level sources. The preamps
are built into the AR2412 rack and their Gain,
Pad and 48V phantom power is remote controlled
from the GLD console via the dSNAKE link. The
output of the analogue preamps are converted to
digital format and transported via dSNAKE to be
processed and mixed at the GLD-80 mixer.
The sockets are numbered 1-24. Any input can
be patched to any channel using the I/O or
Preamp screens. The default is one-to-one
mapping of the input sockets 1-24 to channels 1-
24.
Output sockets 12 balanced XLR outputs
operating at nominal +4dBu line level. Any GLD
signal can be patched to any socket using the
console I/O screen. The default Template Shows
provide a logical mapping of these sockets to get
you started.
EXPANDER port CAT5 cable link to
connect a GLD-AR84 expander rack to add a
further 8 mic/line inputs and 4 XLR line outputs.
The GLD system numbers these sockets as
Inputs 25-32 and Outputs 13-16. This port can
also be used to connect to the Allen & Heath ME
personal mixing system.
MONITOR port CAT5 cable link to connect
to the ME personal mixing system. It is also
compatible with Aviom
®
A-Net 16 when Aviom
mode is selected in the I/O / Monitor screen.
dSNAKE port CAT5 cable link to connect
the AR2412 rack to the GLD-80 mixer. This
carries the 32 inputs, 16 outputs and the monitor
port sends audio to and from the rack as well as
control for the preamps and system status.
Maximum CAT5 cable length is 120m (396’)
depending on cable type.
Note that dSNAKE is not compatible with the
iLive ACE connection.
Fan A low noise fan ensures air movement
through the rack to keep the circuits within
operating temperature range.
Ensure good ventilation at the back of the
rack. Read the safety instructions printed on the
panel and the Safety Sheet packed with the unit.
Mains power input IEC connector, fuse
and power ON/OFF push switch for the built-in
universal voltage power supply unit. This
accepts worldwide voltages from 100 to 240V AC
50/60Hz. Check that you have received the
correct mains lead for your territory.
Secure the cable in place using the plastic P-clip.
Use a T20 Torx screwdriver to refit the screw.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GLD Digital Audio Mixing System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GLD Digital Audio Mixing System in the language / languages: English as an attachment in your email.

The manual is 5,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info