538892

Zelmer 13Z011 Manual

214
Zoom out
Zoom in
Previous page
1/228
Next page
214
13. Preparing hot water
The hot water function is perfect for the preparation of e.g. hot chocolate, for fi lling the coffee pot equipped with a pusher
or fi lling the tea pot.
The appliance is ready to use when the message READY TO BREW appears on the display.
Place a cup or another utensil under the steam/hot water nozzle (16).
Make sure there is water in the tank (3). Turn the knob (13) anticlockwise and set it in the
position. Hot water will come
out of the nozzle and the message HOT WATER PREPARATION will appear on the display.
To stop the hot water function, set the knob (13) again in the OFF position. The message READY TO BREW will again ap-
pear on the display.
ATTENTION! If the 1 minute hot water pumping time is exceeded, the coffee maker will immediately stop working
and return to the READY TO BREW status. To restart this function, set the knob (13) back to the OFF position and
next turn and set the knob (13) in the position . The next pumping of hot water is possible for maximally for
the next minute. Remember not to use the hot water operation mode for 30 minutes after using it for 5 1-minute
intervals.
14. Preparing steam
The steam function is used to froth milk. The steam has two functions. First of all it warms up the milk. It also mixes the
air, which results in a delicate, velvet froth. Similarly to coffee brewing, you will receive best results in frothing milk in the
course of time and with experience.
Tip: Remember that coffee is the base of all coffee beverages, milk is only an addition.
Note: It is recommended to fi rst prepare the coffee and then to froth milk. The steam function can also be used to heat
beverages.
The appliance is ready to use when the message READY TO BREW appears on the display. Make sure there is water in
the tank (3). Press the (D) button. The control lamp of this button will light indicating that the coffee maker is warm-
ing up. The message COFFEE STEAM will appear on the display. The coffee maker will warm up to the set tempera-
ture and will switch to the steam mode. The message READY TO USE STEAM will appear on the display.
Determine the amount of milk based on the number of brewed cups of coffee or the size of the milk jug. ●
Tip: ● Remember that the volume of milk increases during frothing.
Pour cold milk to a stainless steel jug. Fill the jug from 1/3 to 1/2 of its capacity. ●
Tip: ● Store the stainless steel milk jug in the refrigerator, so that the milk is cold. Remember not to rinse the jug with
warm water before use.
Rinse the steam/hot water nozzle ● (16) by placing another appliance under the nozzle and turning the knob (13) an-
ticlockwise to the steam position . After a few seconds, steam will come out of the nozzle (16) and the message
STEAM GENERATION will appear on the display. (Note: The steam is very hot. Burn risk!). Switch off the steam
by turning the knob (13) to the OFF position to stop the steam generating process. The steam nozzle has been pre-
rinsed.
Next, place the steam nozzle ● (16) in the milk jug so that the nozzle is about ½ cm below the surface of milk and acti-
vate the steam function by turning the knob (13) again to the position.
Tilt the jug so that the steam nozzle is inside the jug, lower the jug until the end of the nozzle is just below the milk sur- ●
face. This will cause the milk to froth.
Note: ● Do not allow the steam to escape unevenly, the froth will not be properly aerated. To avoid this situation, lift the
jug so that the steam nozzle is positioned deeper in the milk. Remember the perfect consistency is a soft, velvet froth.
When the milk warms up and becomes frothy, the level of milk in the jug will begin to rise. In this situation, lower the ●
jug, but keep the steam nozzle end just below the milk surface.
Lift the jug upon receiving froth so that the steam nozzle is located in the middle of the milk. ●
Tip: ● The required amount of froth will change depending on the type of the prepared beverage. For example cappuc-
cino requires a larger amount of froth than a coffee beverage on the base of an espresso, served with frothy milk.
Immediately switch off the steam when the milk is heated to the temperature of 60–65°C by turning the adjustment ●
knob (13) to the OFF position.
Tip: ● If you do not have a thermometer, a good indication of the proper temperature is that you cannot place your hand
on the side of the jug for more than 3 seconds.
Important: ● Do not boil the milk.
Remove the jug. Immediately wipe the steam nozzle ● (16) and its end using a damp cloth and rinse with a small amount
of steam proceeding the same way as in the case of before frothing the milk.
Holding the jug in one hand, lightly tap the jug on the table to release the air bubbles and next make a circular move- ●
ment with the jug until the milk becomes shiny and without any bubbles. This will help to receive a uniform consistency
of the milk and froth.
After the end of the steam generating process press the (D) button. The control lamp will go off and the message STEAM
COFFEE will appear on the display indicating that after a fi xed period of time the coffee maker will return to the cof-
fee brewing mode. The message READY TO BREW will appear on the display.
… 214 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 13Z011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 13Z011 in the language / languages: English, Polish as an attachment in your email.

The manual is 15,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info