669800

Yuneec Tornado H920 Industry Manual

27
Zoom out
Zoom in
Previous page
1/39
Next page
NOTICE: The H920 main LED indicator
will blink red and white if the TORNADO
loses GPS signal/lock. The H920 main
LED indicator will be solid color of the
current mode if the GPS signal/lock is
acquired.
NOTICE:
If the model chosen has never been bound before. 'NOT CONNECTED' will
display in the MODEL column, and the remote controller can bind any YUNEEC
SR12/24 receiver. If a series of receiver codes display on the screen, it means the
model was bound before and can't be bound to any other receiver. If you want to bind
this model to other receiver,you can press and hold the model icon in the MODEL
SELECT interface till a pop-up window comes out, tap 'Copy', and then select the
model newly created.
BINDING (TEAM MODE)
BINDING THE TORNADO H920 TO ONE ST24
The copter is already bound in the RC mode. if the pilot wants to bind the copter to
the ST24 transmitter again, you can refer to the following steps:
STEP 1) Power on the ST24, if you are in FPV mode tap [ ] to go to the main interface，
and choose RC.
STEP 2) Tap System Settings icon to enter the Bind interface.
STEP 3) Disconnect the gimbal connector first, and then
switch on the TORNADO H920. Wait until the Main LED
indicator blinks blue, that means the self-inspection of the
H920 is complete.
STEP 4) Lean the H920 in the forward direction twice (45°)
till the Main LED indicator blinks yellow.
STEP 5) Tap the Refresh icon, and the code of the H920 will be shown on the screen.
Select the right code and tap Bind. Tap OK when a pop-up window comes out.
STEP 6) When tapping [ ] , you will hear two long beeps from the aircraft. That means
the ST24 Remote Controller is bound to the H920 successfully.
26
NOTICE:
When the V18/CGO4 is attached to the TORNADO H920, the control slider
V18/CGO4 Zoom In/Out Control Slider (K6)-located on the right side of the
controller-is activated. Users can zoom in or zoom out by switching K6. When zooming
in,V18/CGO4 gimbal camera in pitch and yaw directions will become slow in the
velocity mode. When zooming out, the movement speed of the V18/CGO4 gimbal
camera in pitch and yaw directions will become fast in the velocity mode.
CAUTION:
We recommend that the CGO4/V18 gimbal camera should be operated
according to the above steps strictly, otherwise it may cause unexpected results of lens
failing to retract or video loss etc.
NOTICE: When using GB603, press the stop recording button to save the images first,
then power off the H920, and turn off the camera at last
When using CGO4, stop recording first, then switch off the camera by ST-24, and
switch off the H920 at last.
When using V18 first stop recording then switch off the H920.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Industry at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Industry in the language / languages: English as an attachment in your email.

The manual is 3,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info