669800

Yuneec Tornado H920 Industry Manual

26
Zoom out
Zoom in
Previous page
1/39
Next page
CAMERA CONTROLS (SINGLE MODE)
GIMBAL PITCH CONTROL (GB603 GIMBAL AND V18/CGO4 GIMBAL CAMERA)
There is a gimbal pitch mode switch on ST24---S1. When the switch is in up/middle
position, the GB603 gimbal/V18/CGO4 gimbal camera is in Angle Mode. Use the
slider (C) on the left side of the ST24 to set the pitch/tilt position of the gimbal/gimbal
camera. When the S1 is in bottom position, the gimbal/gimbal camera is in Velocity
Mode. When the slider (C) is in the middle position, it means the velocity rate is 0 for
the GB603/CGO4/V18, and it will stop pitching up/down. When the slider (C) is above
the middle position, the GB603/CGO4/V18 will start pitching up. When the slider (C)
is below the middle position, the GB603/CGO4/V18 will start pitching down. The
distance between the slider (C) and the middle position decides the velocity rate, the
further distance, the higher velocity it would be.
NOTICE: When the V18/CGO4 is attached to the TORNADO H920, the control slider
V18/CGO4 Zoom In/Out Control Slider (K6)-located on the right side of the
controller-is activated. Users can zoom in or zoom out by switching K6. When zooming
in,V18/CGO4 gimbal camera in pitch and yaw directions will become slow in the
velocity mode. When zooming out, the movement speed of the V18/CGO4 gimbal
camera in pitch and yaw directions will become fast in the velocity mode.
CAUTION:
You MUST stop recording video in order to take still photos. It will take
approximately 5 seconds to capture a still photo and before you can take another.
CAUTION: ALWAYS stop recording video before turning off the TORNADO H920/V18
/CGO4 to avoid data loss.
CAMERA/GIMBAL YAW CONTROL
There is a gimbal yaw mode switch on ST24---S2.
When the switch position is up and middle, the
gimbal/gimbal camera is in Follow Mode. The
yaw control of the gimbal/camera is now
disabled. The gimbal/camera will adjust its yaw
direction according to the aircraft’s movements.
When the switch position is down, the
gimbal/gimbal camera is in Global Mode. The
Gimbal Yaw control knob (K1) is now activated.
When the user rotates the knob in the right
direction, the gimbal/gimbal camera will rotate
to the right side, and vice versa.
Button A = Take Still Photo Button B = Start/Stop Recording Video
25
SELECT interface till a pop-up window comes out, tap 'Copy', and then select the
model newly created.
NOTICE: We recommend users to power on the aircraft in the angle mode.
NOTICE: After the camera is selected successfully, when you press [ ], you will hear
two long beeps. That means the binding is complete. The Real-time images can now
be seen on the screen.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Industry at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Industry in the language / languages: English as an attachment in your email.

The manual is 3,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info