669800

Yuneec Tornado H920 Industry Manual

29
Zoom out
Zoom in
Previous page
1/39
Next page
28
CAMERA CONTROLS (TEAM MODE)
NOTICE: The ST24 mentioned in this chapter is the one bound to the Gimbal/Camera.
GIMBAL PITCH CONTROL (GB603 AND V18/CGO4 GIMBAL CAMERA)
There is a gimbal pitch mode switch on ST24---S1. When the switch is in up position, the
gimbal/gimbal camera is in Angle Mode. Use the K5 (C) of the ST24 to set the pitch/tilt
position of the gimbal/gimbal camera. When the S1 is in bottom position, the
gimbal/gimbal camera is in Velocity Mode. When the right-hand stick is in the middle
position, it means the velocity rate is 0 for the GB603 or V18/CGO4, and it will stop
pitching up/down. When the right-hand stick is above the middle position, the GB603 or
V18/CGO4 will start pitching up. When the right-hand stick is below the middle position, the
GB603 or V18/CGO4 will start pitching down. The distance between the right-hand stick and the
middle position decides the velocity rate, the further distance, the higher velocity it would be.
CAUTION:
You MUST stop recording video in order to take still photos. It will take
approximately 5 seconds to capture a still photo and before you can take another.
CAUTION: ALWAYS stop recording video before turning off the TORNADO
H920/V18/CGO4 to avoid data loss.
CAMERA/GIMBAL YAW CONTROL
There is a gimbal yaw mode switch on ST24---S2. When the switch
position is up, the gimbal/gimbal camera is in Follow Mode. The yaw
control of the gimbal/camera is now disabled. The gimbal/camera will adjust its
yaw direction according to the aircraft’s movements.
when the switch is in the middle position, the gimbal camera is still in
Follow Mode, however, at this time, the yaw control is activated. The
gimbal camera will adjust its yaw direction according to the aircraft’s movements.
When the switch position is down, the gimbal/gimbal camera is in Global Mode. The
Aileron/Roll Control of the right-hand stick take control of the GB603/V18/CGO4 in yaw directions.
Button A = Take Still Photo Button B = Start/Stop Recording Video
NOTICE: When the V18/CGO4 is attached to the TORNADO H920,
V18/CGO4 Zoom In/Out Control Slider (K6)-located on the right side of
the controller-is activated. Users can zoom in or zoom out by switching
K6. When zooming in,V18/CGO4 gimbal camera in pitch and yaw
directions will become slow in the velocity mode. When zooming out,
the movement speed of the V18/CGO4 gimbal camera in pitch and yaw
directions will become fast in the velocity mode.
NOTICE: When using GB603 to switch off the TORNADO, press the stop recording button
to save the images first, then power off the H920 and turn off the camera at last. When
using CGO4 first stop recording then switch off the camera by ST-24 and switch off the
H920 at last. When using V-18 first stop recording then switch off the H920.
CAUTION:
Each time the K6 is pushed to a certain position, it should be pushed back to the
middle position to confirm the setting. Otherwise, the gimbal camera will continue to zoom
in/out until it achieves the maximum/minimum value.
CAUTION: We recommend that the CGO4/V18 gimbal camera should be operated according
to the above steps strictly, otherwise it may cause unexpected results of lens failing to retract
or video loss etc.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yuneec Tornado H920 Industry at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yuneec Tornado H920 Industry in the language / languages: English as an attachment in your email.

The manual is 3,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info