734892
9
Zoom out
Zoom in
Previous page
1/31
Next page
9
NOTICE:
ALWAYS apply a small amount of lubricant on
o-rings prior to assembling the garden hose to the pump (C),
high pressure hose (D), spray gun (E), and spray wand (F).
Lubricate all connections shown below, following these
instructions:
1) Inspect and clean connecting surfaces prior to lubrication
and assembly.
2) Use lubricants sparingly during assembly; a light lm is
all that is required.
3) Use a small brush or cotton swab to apply grease directly
to o-rings where they are not accessible(QC tting, M22
tting).
6.Connect Hose and Water Supply to Pump
IMPORTANT! DO NOT run the pump without the water
supply connected and turned on.
Damage to pressure washer resulting from failure to follow
this instruction will void warranty.
NOTICE:
Remove and discard the shipping caps from the
pump’s high pressure outlet and water inlet before attaching
hoses.
1) Uncoil high pressure hose when handle folded, and
attach one end of hose to the base of the spray gun.
Tighten by hand. The other end already assembled to
the pump at the factory.
NOTICE:
The hose only can be uncoiled from the bottom of
the hose reel, it’s recommended to keep the handle folded
for easy unwinding and winding the hose.
WARNING! The high pressure stream of water that the
pressure washer produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER connect high pressure hose to spray wand.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
Always be certain spray gun, wand, nozzles and other
accessories are correctly attached.
2) Before you connect your garden hose to the water inlet,
inspect the inlet screen. Clean the screen if it contains
debris or have it replaced if damaged. Do Not run
the pressure washer if the inlet screen is damaged or
missing.
IMPORTANT! NEVER siphon standing water for the water
supply. Use only cold water (less than 100 °F).
CAUTION! Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or inlet
connector damage.
1) There must be at least 10 ft. (3 m) of unrestricted garden
hose between pressure washer inlet and any device,
such as a vacuum breaker or check valve.
2) Damage to pressure washer resulting from failure to
follow this instruction will void warranty.
3) Run water through garden hose for 30 seconds to ush it
of debris. Turn o water.
4) Connect garden hose (not to exceed 50 ft. in length) to
water inlet. Tighten by hand.
WARNING! Risk of eye injury!
Spray could splash back or propel objects resulting
in serious injure.
Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of the pressure washer.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
E
F
C
D
Inspect inlet screen. Do Not use if
damaged, clean if dirty
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce Y0GWC3200R0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce Y0GWC3200R0 in the language / languages: English as an attachment in your email.

The manual is 7,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info