733774
28
Zoom out
Zoom in
Previous page
1/33
Next page
54 55
Set cut time
This option determines the working periods of the mower in a day. A maximum
of three working periods (T1 to T3) can be set. Select a working period and then
use the number keys on the display for inputting the start and end times for each
working period.
If the mower runs out of battery power within a working period, it will automatically return
to the charging station for charging and then work again until the working period ends. It is
best to rst leave the working periods as factory defaults and then modify if required after
you know the time the mower takes to completely cut the lawn. Remember that the mower
may take longer time to cut the same lawn in different seasons or under different weather
conditions.
History
There are four further options in “History”.
Fault
This option shows the last 4 fault records. Error information includes:
Message Description
Low Battery The battery power is too low to get back to the charging station.
No signal There is no boundary cable signal.
Outside The mower has moved outside the mowing zone.
Trapped
The obstacle sensor gives continuous alert for more than
10 seconds. The mower has stopped for safety reasons.
Pit
The obstacle sensor has triggered more than 10 times in one minute. The
mower has stopped for safety reasons.
Slope
The mower has encountered a steep slope which it cannot
overcome.
Lifted The mower has either been lifted up or risen up over an obstacle.
Error(XX) See the section: Error codes.
Cutting
This option shows the start and end times of the last two mowing cycles.
Charge
This option shows the end times and voltages of the last two charging cycles.
Health
This option shows an overview of the total working time and number of charging
cycles.
Language
This option determines the language used in the control menu. The languages available for
selection are: English, Swedish, German, Danish, Spanish, Finnish, French, Italian, Dutch and
Norwegian.
Date
This option sets the date and time for the control menu. Select the option “Date” to set the
current date and the option “Time” to set the current time. Use the number keys on the
display for inputs.
Note
All programmed activities and records in the mower will be based on the
date and time set in this option.
Install
This option starts the test running mode.
In this mode, the mower will mow for one minute and then return to the charging
station. After one minute of charging, the mower will start mowing again. This mode
is used mainly for setup checking.
OPERATION
OPERATION
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce SA800PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce SA800PRO in the language / languages: English as an attachment in your email.

The manual is 6,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info