733774
30
Zoom out
Zoom in
Previous page
1/33
Next page
58 59
Cleaning the underside
Ensure the main power switch (11) is in OFF position. Wear protective gloves. Turn the
Robomower onto its side to expose its underside. Clean the blade disc and frame using a soft
brush or damp cloth. Rotate the blade disc to make sure that it moves freely, and check that the
blades can turn on their pivots and no grass is obstructing them.
Clean the contact pins and the charging strips
Using wire wool, metal cleaner or very ne grade emery paper, clean the contact pins and
the charging strips on your mower and charging station. Remove any debris, leaves or grass
clippings around the contact pins and charging strips to ensure efcient charging.
Reversing or replacing the blades
WARNING!
Ensure the Robomower is completely shut off before cleaning, adjusting or replacing
the blades. Always wear protective gloves.
WARNING!
To ensure maximum cutting efciency and safety, always use recommended
replacement blades and blade mounting parts when replacing.
Your Robomower has three blades xed to the blade disk.
Unless damaged by hard obstacles, these blades can last for up to ve months with everyday
use.
Weekly inspection of the blades and the xing screws is required. Note that the blades are
double-edged. Once the rst side is blunt, loosen the xing screw. Turn the blade upside-
down and x it again with the xing screw. After tightening the xing screw, verify that the
blade can rotate freely around the screw.
A set of spare blades is included with the Robomower. More are available from customer
support. The blade's spare part number is 846210.
Only use original spare parts. For best performance and avoiding imbalance, always turn or
replace all three blades at the same time.
Replacing the battery
While the actual battery life will depend on usage and environmental factors, the typical
service life is several years. Spare batteries are available from customer support. To
replace the battery, please follow the instructions below.
1) Ensure the main power switch (11) is turned OFF. Clean the underside as instructed.
2) Set the Robomower to the lowest cutting height.
3) Turn the mower upside-down. Remove the 5 screws xing the battery compartment's lid.
Note one screw is partially covered by the blade protector and is only accessible through
a service hole.
4) Pull out the battery and disconnect it from the Robomower.
5) Carefully clean the lid and the edge of the battery compartment. Debris may allow
excessive water to enter the battery compartment, causing major damage to the device.
6) Connect and insert the replacement battery, close the compartment and x the lid with 5
screws. Do not turn on the Robomower before placing it back on its wheels - beware of
sharp blades!
CLEANING/MAINTENANCE CLEANING/MAINTENANCE
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce SA800PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce SA800PRO in the language / languages: English as an attachment in your email.

The manual is 6,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info