689861
301
Zoom out
Zoom in
Previous page
1/363
Next page
7B-2
Chapter 7 Part B Frame and bodywork (XV700-1100 models)
4.1 Remove one mounting nut, detach the prop rod and remove
the other mounting nut
5.1a The sidestand spring must be properly connected
and in good condition
removing the right rear footpeg assembly on an early shaft drive
model, support the exhaust system and unbolt the footpeg from the
frame (the same boit also secures an exhaust bracket).
3 To remove a footpeg assembly on chain drive models, remove the
pivot bracket nut and washer from the inside of the alloy bracket.
4 Installation is the reverse of removal. Lubricate the footpeg pivots
(see Chapter 1).
4 Seat - removal and installation
Refer to illustration 4.1
1 If you're working on a hinged seat, unlock and lift the seat and
remove one of the mounting nuts (see illustration). Detach the prop
rod, then remove the remaining mounting nut.
2 If the seat is secured by clips, unlock it, then detach it from the
clips.
3 If you're working on a bolted seat (1984 and later models),
remove the bolts (one on each side at the front of the seat). Detach the
rear of the seat from its bracket and lift it off.
4 Installation is the reverse of the removal steps.
5 Sidestand and centerstand - maintenance
Refer to illustrations 5.1a and 5.1b
1 The sidestand (and centerstand on models so equipped) is
attached to the frame. An extension spring(s) anchored to the bracket
ensures that the stand is held in the extended or retracted position
(see illustrations).
2 Make sure the pivot bolt or nuts are tight and the extension spring
is in good condition and not overstretched. An accident is almost
certain to occur if the stand extends while the machine is in motion.
6 Sidestand and centerstand - removal and installation
1 Support the bike securely so it can't be knocked over during this
procedure.
2 Unhook the spring (see illustration 5.1a or 5.1b). Remove the
pivot bolt or nuts and take the stand off the pivot shaft(s).
3 Installation is the reverse of the removal steps.
7 Side covers - removal and installation
1 Side covers on all models are secured by rubber grommets. In
some cases, posts fit into the grommets; in other cases, a slot in the
edge of the cover fits into a slot in the grommet.
2 To remove a side cover, pull it gently to disengage the cover from
the grommets. Caution: Don't force the cover loose. If it won't come
easily, make sure you're pulling in the right direction.
3 Installation is the reverse of the removal steps.
5.1b ... the centerstand spring must also
be properly connected and in
good condition
8.1 Remove the fender/mudguard
mounting bolts
8.2 Slip the speedometer cable out
of the guide
301


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha XV920 Virago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV920 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info