571272
263
Zoom out
Zoom in
Previous page
1/300
Next page
Reference Utility Mode
Utility mode
263
Owner’s Manual
SongEventChase Event Chase allows you to specify which non-note data types are properly recognized during fast-forward and
rewind operations. Normally, if a Song or Pattern is played back from mid-point and/or fast-forward or rewind are
used, certain data types (such as Program Change, Pitch Bend, and Control Change) may not play back as
expected. Setting this to a specific event ensures the playback integrity of the event, even when fast forwarding or
rewinding.
Settings: Off, PC (Program Change), PC+PB+Ctrl (Program Change+Pitch Bend+Control Change), all (All events)
nKeep in mind that settings other than “off” may result in slower operation — for example, a pause before starting playback, or
slower rewind/fast forward speed.
nWhen this is set to “all,” an excessive amount of MIDI data may be generated, possibly resulting in a MIDI error on the
connected device.
DumpInterval (Bulk Dump
Exclusive Interval Time) When playing back system exclusive data (bulk data) that is recorded on the sequence tracks, this sets the interval
that is inserted for each 1KB.
When sending bulk data from this synthesizer to a connected MIDI device, a MIDI error may result if the device
cannot handle large amounts of data in a short time. This parameter compensates for that by setting an interval that
provides enough time for the receiving device to process the bulk data.
Settings: 0 ~ 900 (msec)
nThe playback may be a little slower depending on the currently set interval. Also when a MIDI error occurs, try to set the
interval a little higher and send the data again.
LoadMix Determines whether the Mixing settings are loaded (on) or not (off) when the Song/Pattern number is changed.
Settings: off, on
nThis setting affects the Song/Pattern change during Song/Pattern chain playback.
SendXGOn
ToMultiPartPB Determines whether an XG reset message is sent to the Multi-part Plug-in board tone generator block (on) or not
(off) when starting an XG song or changing the Song/Pattern number.
Settings: on, off
[F4] CTL ASN (Controller Assign)
[SF1] ARP (Arpeggio)
Switch Determines the Control Change Number that controls on/off status of Arpeggio playback.
Settings: 00~95
Hold Determines the Control Change Number that controls on/off status of Arpeggio Hold (page 189).
Settings: 00~95
[SF2] ASSIGN From this display you can assign specific functions to the ASSIGN A and B knobs (when the [PAN/SEND] and
[TONE] lamps are on).
ASA (Assign A)
Dest (Destination) Two parameters are available here. The first (ASA) determines the Control Change number generated by the
ASSIGN A knob. The second, Destination (Dest), determines what parameter or aspect of the sound is affected by
the knob. Keep in mind that if the same MIDI Control Change messages as set here are received from an external
device, the internal tone generator also responds to those messages.
Settings: Refer to the separate Data List booklet.
ASB (Assign B)
Dest (Destination) Two parameters are available here. The first (ASB) determines the Control Change number generated by the
ASSIGN B knob. The second, Destination (Dest), determines what parameter or aspect of the sound is affected by
the knob. Keep in mind that if the same MIDI Control Change messages as set here are received from an external
device, the internal tone generator also responds to those messages.
Settings: Refer to the separate Data List booklet.
[SF3] FT SW (Footswitch) From this display you can determine the Control Change number generated by using the Footswitch connected to
the ASSIGNABLE jack. Keep in mind that if the same MIDI Control Change messages as set here are received from
an external device, the internal tone generator also responds to those messages as if the Footswitch of the
instrument was used.
Settings: 000~100 (000, 032: off, 096: Arpeggio Switch, 097: Arpeggio Hold, 098: Song/Pattern playback start/stop, 099/100: Program
Change INC/DEC 101: Octave Rest)
[SF4] REMOTE Two different computer sequencer control modes can be selected here, as well as the respective MIDI port settings
for control. When you’ve made the desired settings, press the [ENTER] button to actually call up the preset control
templates for the software. For details, refer to the Quick Guide on page 147.
[SF5] MEF (Master Effect) From this display you can set the parameters related to the Master Effect Knob operations. (Press both the [ARP FX]
and [EQ] buttons so that their lamps light.)
Knob1 ~ Knob4 Assigns a parameter of the Master Effect to each knob. Available parameters differ depending on the selected
Master Effect type.
[F5] MIDI
[SF1] CH (Channel) From this display you can make basic MIDI settings.
BasicRcvCh
(Basic Receive Channel) Determines the MIDI receive channel when this synthesizer is set to single-timbre tone generator mode (Voice/
Performance modes).
Settings: 1~16, omni (all channels), off
nIn the multi-timbral tone generator mode (Song/Pattern modes), each Part receives MIDI data according to its assigned MIDI
receive channel ([SONG] or [PATTERN] [MIXING] [EDIT] Part selection [F1] VOICE [SF2] MODE ReceiveCh).
263


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MOTIF ES7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MOTIF ES7 in the language / languages: English as an attachment in your email.

The manual is 8,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MOTIF ES7

Yamaha MOTIF ES7 Installation Guide - English - 35 pages

Yamaha MOTIF ES7 Installation Guide - German - 35 pages

Yamaha MOTIF ES7 User Manual - German - 300 pages

Yamaha MOTIF ES7 User Manual - Dutch - 300 pages

Yamaha MOTIF ES7 User Manual - French - 300 pages

Yamaha MOTIF ES7 Installation Guide - French - 35 pages

Yamaha MOTIF ES7 User Manual - Italian - 308 pages

Yamaha MOTIF ES7 Installation Guide - Italian - 12 pages

Yamaha MOTIF ES7 User Manual - Portuguese - 300 pages

Yamaha MOTIF ES7 User Manual - Spanish - 297 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info