Sampling Record mode When entering the Sampling mode from the Song mode/Pattern mode
254Owner’s Manual
WAITING (Trigger Waiting or
Punch-in Waiting)
When Trigger Mode is set to “level” in the Sampling Standby display, press the [F6] REC button again to enter the
Trigger Waiting condition; the [F6] menu changes to “STOP.” In this condition, sampling will begin as soon as an
input signal exceeding the specified trigger level is received.
When the Trigger Mode is set to “meas” in the Sampling Standby display, press the [F6] REC button again to enter
the Punch-in Waiting condition; the [F6] menu changes to “STOP.” In this condition, sampling will begin as soon as a
song or pattern playback reaches the punch-in measure.
Before recording starts in either condition, press the [F6] STOP button or [EXIT] button to return to the Sampling
Standby display. Keep in mind that the Confirm function can be tuned on or off by using the [F2] CONFM button also
in the Trigger Waiting or Punch-in Waiting condition if the Sampling type is set to other than “slice+seq.”
RECORDINGDuring recording, press the [F6] STOP button or [EXIT] button to stop sampling.
After sampling (recording) stops:
The following menus appear when the Sampling type is set to “sample” or “sample+note” and the Confirm function
is turned on.
[F3] AUDITIONPressing this lets you hear the sample obtained by recording (sampling).
[F4] CANCELPressing this deletes the sample obtained by recording (sampling) and return to the Sampling Standby display.
[F5] OKPressing this stores the sample obtained by recording (sampling) to the specified destination.
TRIM/SLICE display after
sampling stops
If you’ve entered the Sampling Record mode for the Song or Pattern mode and you’ve set the sampling type to
“slice+seq,” you should set the following Slice related parameters after the Sampling stops.
Please note that the Confirm function is not available in this case.
[F1] TRIM
The trim function makes it possible to specify the beginning and end points to be played back within an entire sample. You can also specify the tempo for
the range of the looped playback and determine its beat.
Start (Start Point)Determines the Start point for the sample playback.
Loop (Loop Start Point)
Determines the Top point of the loop playback (the point where the loop begins) within the range of the entire sample.
End (End Point)Determines the End point of the loop playback within the range of the entire sample.
BeatIndicates the (beat) and tempo of the range from the Loop Start Point to the End Point.
[SF1] AUDITIONPress the [SF1] button to sound the recorded sample according to the settings in this display.
[SF2] LP=STWhen the menu indication here is “LP=ST,” the Start (Start Point) and the Loop (Loop Start Point) will share the same
address, meaning that both of them will be changed simultaneously, even if just one of them is changed. Pressing
the [SF2] button in this condition changes the menu from “LP=ST” to “LP≠ST.” When the menu indication here is
“LP≠ST,” the Start (Start Point) and the Loop (Loop Start Point) can be changed independently. When pressing the
[SF2] button in this condition, the address value of the Start will be copied to that of the Loop, with the result that
both of them will have the same address value. The menu indication also changes from “LP≠ST” to “LP=ST.”
[SF3] SET ENDPressing this calls up the display for determining the End Point, from which you can set the tempo, beat, and
measure for the sample. Press the [ENTER] button to actually set End Point. If you are satisfied with the results
(press [SF1] to audition the sample), press the [F6] OK button to return to the original display. Doing this stores your
edited sample to the DIMM memory. To return to the original display without changing the data, press the [F5]
CANCEL button.
[SF4] EXTRACTDelete all unnecessary sample data located ahead of the Start point and located after the End point) by pressing the
[SF4] button.
[F5] ZOOM-
[F6] ZOOM+
Press the [F5] and [F6] buttons to zoom in and out of the wave display.
[F2] SLICE
This powerful feature lets you automatically divide the recorded sample into separate “slices.” These slices are then assigned to successive notes and
arranged as sequence data.
nBefore executing the Slice operation, you’ll need to accurately adjust the length of the sample. Use the [SF1] AUDITION button in the [F1] TRIM display to loop the sample
and precisely set the Start and End points as required.
After specifying the following parameters, press the [ENTER] button. (The display prompts you for confirmation.) Press the [INC/YES] button to execute the
Slice. You can hear and confirm the sliced samples by pressing the [SF1] AUDITION button. If you are satisfied with the result of the operation, press the
[F6] OK button to store the result of the Slice operation and go back to the Sampling Setup display. If not, press the [F5] CANCEL button to go back to the
Sampling Setup display without storing the result.
Type (Slice Type)Specifies how the sample is sliced, and to some extent determines the resulting sound quality. Select the type that
best suits the original phrase.
Settings:beat1~3, phrase1~4, quick
beat1~3...........This slice type is suited for percussive phrases such as drums or bass with a fast attack and short decay. Three
variations are provided.
phrase1~4.......Ideal for phrases containing cymbals or other instruments with a long decay. Four variations are provided.
quick................Regardless of the phrase content, the sample is divided at the specified note sub-divisions. The number of slices per
measure is calculated by multiplying the top number of the Meter (time signature) parameter by the bottom number of
the SubDivide parameter.
nFor helpful hints on getting the Slice Type parameter to work for different samples, see “Tips for using the Slice Types” on page
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha MOTIF ES7 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha MOTIF ES7 in the language / languages: English as an attachment in your email.
The manual is 8,4 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
