nWhen the Source is set to any of mLAN1~4 and the mLAN terminal is used as an audio input, the Frequency is fixed to 44.1
kHz and cannot be changed.
nAt settings other than 44.1 kHz, the sound monitored during recording may be different from the recorded sound, depending
on the source signal.
[F6] REC
Even if you press the [F6] REC button, recording (sampling) will not start immediately. Set various parameters such as Trigger Mode in the Sampling Standby
display, then start the actual sampling according to the settings.
STANDBY (Sampling Standby)Press the [REC] button to enter the Sampling Standby display. From this display you can turn the Confirm function on
or off by pressing the [F2] CONFM button as well as set parameters listed below. For details on the Confirm function,
refer to page 95 in the Quick Guide section.
TrggrMode (Trigger Mode)Specifies the method by which sampling will be triggered.
Settings:level, manual
level..................When this is selected, press the [F6] REC button to enable the Trigger Waiting condition. Sampling will then begin as
soon as an input signal exceeding the specified trigger level is received. When this is selected, you need also set the
Trigger Level (1~127).
manual.............When this is selected, sampling will begin as soon as the [F6] START button is pressed, regardless of the input signal
level.
KeyThis is the same parameter as Keybank in the [F1] DEST display.
RecMonitor (Recording Monitor)Determines the output level of the monitor for the input signal.
This monitor signal is output from the PHONES jack or the OUTPUT R and L/MONO jacks. This has no effect on the
recording level.
Settings:0 ~ 127
RecGain (Recording Gain)Determines the recording gain when resampling. This parameter is available only when the Source is set to
“resample.”
Settings:-12dB ~ +12dB
WAITING (Trigger Waiting)When Trigger Mode is set to “level” in the Sampling Standby display, press the [F6] REC button again to enter the
Trigger Waiting condition; the [F6] menu changes to “STOP.” In this status, sampling will begin as soon as an input
signal exceeding the specified trigger level is received. Before recording starts, press the [F6] STOP button or
[EXIT] button to return to the Sampling Standby display.
Keep in mind that the Confirm function can also be turned on or off by using the [F2] CONFM button in the Trigger
Waiting condition.
RECORDING During recording, press the [F6] STOP button or [EXIT] button to stop the sampling.
After sampling (recording) stops:
The following menus appear only when the Confirm function is turned on.
[F3] AUDITIONPressing this lets you hear the sample obtained by recording (sampling).
[F4] CANCELPressing this deletes the sample obtained by recording (sampling) and return to the Sampling Standby display.
[F5] OKPressing this stores the sample obtained by recording (sampling) to the specified destination.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha MOTIF ES7 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha MOTIF ES7 in the language / languages: English as an attachment in your email.
The manual is 8,4 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
