478504
29
Zoom out
Zoom in
Previous page
1/132
Next page
Page 27FT-950 OPERATING MANUAL
TO
1
ANT
DC IN
2
FROM
GND
ROT LINEAR TUNER PTT REC REM KEY
DMU CAT
EXT
SPKR
-TUNE
-TUNE
INPUT
22 A
: DC 13.8 V
REAR PANEL
ANT 1/2 Jacks
Connect your main antenna(s) here, using a type-M
(PL-259) connector and coaxial feed lines. The inter-
nal antenna tuner affects only the antenna(s) connected
here, and only during transmission.
Warning!
The 100V RF voltage (@100 W/50 ) is applied to
the TX RF section of the transciver while transmit-
ting. Do not touch the TX RF section absolutely
while transmitting.
DC IN Jack
This is the DC power supply connection for the trans-
ceiver. Use the supplied DC cable to connect directly
to a DC power supply, which must be capable of sup-
plying at least 22 A @13.8 VDC.
GND
Use this terminal to connect the transceiver to a good
earth ground, for safety and optimum performance. Use
a large diameter, short braided cable for making ground
connections, and please refer to page 9 for other notes
about proper grounding.
To prevent the damage from a thunder, at-
mospheric electricity, electrical shock etc.,
please take a good earth ground.
µ-TUNE Jacks
These jacks are used to connect the optional RF µTun-
ing Kit, signal in and signal out.
ROT
(
ROTATOR
)
Jack
This covered 6-pin MINI-DIN Jack accepts a cable to
connect to a YAESU G-800DXA/-1000DXA/-
2800DXA (for USA/EXP market) or G-800DXC/-
1000DXC/-2800DXC (for European market) Antenna
Rotator (listed models are current as of early 2010).
You may control the antenna azimuth, rotation, and
rotation speed, using the
[
BAND
]
buttons on the front
panel.
LINEAR Jack
This 10-pin output jack provides band selection data,
which may be used for control of optional accessories
such as the VL-1000 Solid-state Linear Amplifier.
Pinout is shown on page 15.
TUNER Jack
This 8-pin output jack is used for connection to the
FC-40 External Automatic Antenna Tuner. Pinout is
shown on page 15.
RTTY/PKT Jack
This 6-pin input/output jack accepts AFSK input from
a Terminal Node Controller (TNC); it also provides
fixed level (100-mV @600 Ohms) receiver audio out-
put, and FSK keying line. Pinout is shown on page 15.
PTT Jack
This RCA input jack may be used to provide manual
transmitter activation using a footswitch or other
switching device. Its function is identical to the
[
MOX
]
button on the front panel. The same line is available at
the RTTY/PKT jack for TNC control. Open-circuit
voltage is +5 VDC, and closed-circuit current is 1 mA.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-950 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info