478504
23
Zoom out
Zoom in
Previous page
1/132
Next page
Page 21FT-950 OPERATING MANUAL
FRONT PANEL CONTROLS & SWITCHES
[
TXW
] (
TX Watch
)
Switch
Pressing this button lets you monitor the transmit fre-
quency when split frequency operation is engaged.
Release the button to return to normal split frequency
operation.
[
C.S
]
Switch
Press this button momentarily to directly recall a fa-
vorite Menu Selection.
To program a Menu selection to the
[
C.S
]
button: press
the
[
MENU
]
button to enter the Menu. Select the Menu
item you want to set as the short cut. Then press and
hold in the
[
C.S
]
button for one second; this will lock
in the selected Menu item as the short cut.
[
MENU
]
Switch
This button is used to access the Menu system. The
various transceiver characteristics may be configured.
Menu operation is described in detail, in this manual,
beginning on page 104.
IMPORTANT NOTE:
Pressing this button momentarily, activates the Menu.
The Menu items will appear on the display; once you
have changed the parameters, you must press and hold
in the
[
MENU
]
button for one second to save any con-
figuration changes (momentarily pressing the
[
MENU
]
button to exit will not save the changes).
Main Tuning Dial Knob
This large knob adjusts the operating frequency of the
VFO-A or a recalled memory. Clockwise rotation of
this knob increases the frequency. Default tuning in-
crements are 10 Hz (100 Hz in AM and FM modes);
when the
[
FAST
]
button is pressed, the tuning steps
increase. The available steps are:
ADVICE:
The tuning steps for the Main Tuning Dial knob are
set, at the factory, to 10 Hz per step. Via Menu item
084 TUN DIALSTP”, however, you may change this
setting from 10 Hz to 1 or 5 Hz instead.
[(
VFO-A
)
TX
]
Indicator/Switch
When this button is pushed, the LED inside the button
will glow red; and, when the PTT switch is pressed,
the transceiver will transmit on the VFO-A frequency
(subject to any Clarifier offset, of course).
ADVICE:
If this indicator is not illuminated, it means the
[(
VFO-
B
)
TX
]
Indicator/Switch has been selected (it will be
glowing red). In this case, transmission will be on the
frequency and mode programmed for VFO-B.
OPERATING MODE
LSB/USB/CW/RTTY/PKT
(
LSB
)
AM/FM/PKT
(
FM
)
Numbers in parentheses indicate steps when the
[
FAST
]
button is On.
1 STEP
10 Hz
(
100 Hz
)
100 Hz
(
1 kHz
)
1 DIAL ROTATION
10 kHz
(
100 kHz
)
100 kHz
(
1 MHz
)
[
FAST
]
Switch
Pressing this button will change the tuning rate of the
Main Tuning Dial knob (VFO-A) or the VFO-B Tun-
ing Knob
([
CLAR/VFO-B
]
knob
)
to 100 Hz/step.
When this function is activated, the “ ” icon ap-
pears in the display.
ADVICE:
This switch affects VFO-A and VFO-B independently.
[
LOCK
]
Switch
This button toggles locking on/off for the Main Tun-
ing Dial knob (VFO-A) or the VFO-B Tuning Knob
([
CLAR/VFO-B
]
knob
)
. With “Lcok” on, the Main
Tuning Dial knob or
[
CLAR/VFO-B
]
knob can still
be turned, but the frequency will not change, and the
” icon appears in the display.
ADVICE:
This switch locks VFO-A and VFO-B independently.
[
A
B
]
Switch
Press this button momentarily to transfer the frequency
or memory channel data, from VFO-A to VFO-B, over-
writing any previous contents in VFO-B. Use this key
to set both VFO-A and VFO-B to the same frequency
and mode.
[
A
B
]
Switch
Pressing this button momentarily, exchanges the fre-
quency or memory channel data, of VFO-A and VFO-B.
[
V/M
]
Switch
This button toggles frequency control between VFO-
A and the memory system. In memory mode, either
” or “ ” icon will be shown under the frequency
Display field to indicate the current selection. If you
have tuned the frequency off the Memory channel, the
” icon will be displayed. Pressing the
[
V/M
]
but-
ton returns the display to the original memory fre-
quency, and the “ ” icon will again be displayed.
Pressing it once more returns frequency operation to
the VFO-A, and the icon will no longer be displayed.
[
M
A
]
Switch
Pressing this button momentarily, will display the con-
tents of the currently-selected memory channel for 10
seconds.
Holding
[
M
A
]
button in for one second copies the
data from the selected memory to VFO-A, and two
beeps sound. Previous data in VFO-A will be over-
written.
[
A
M
]
Switch
Pressing this button momentarily, displays the contents
of the currently-selected memory channel for 10 seconds.
Pressing and holding in this key for one second (until
the double beep) copies the current operating data into
the currently selected memory channel, overwriting any
previous data stored there.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-950 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info