478472

Yaesu FT-250R Manual

25
Zoom out
Zoom in
Previous page
1/44
Next page
FT-250R OPERATING MANUAL 21
The FT-250R allows you to scan just the memory channels, the entire operating band, or
a portion of that band. It will halt on signals encountered, so you can talk to the station(s)
on that frequency, if you like.
Scanning operation is basically the same in each of the above modes. Before you begin,
take a moment to select the way in which you would like the scanner to resume scanning
after it halts on a signal.
Setting the Scan Resume Technique
Three options for the Scan-Resume mode are available:
5 SEC5 SEC
5 SEC5 SEC
5 SEC: In this mode, the scanner will halt on a signal it encounters, and will hold there for
5 seconds. If you do not take action to disable the scanner within that time period,
the scanner will resume even if the stations are still active.
BUSYBUSY
BUSYBUSY
BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds after the
carrier has dropped because the other station(s) ceased transmission, the scanner
will resume.
HOLDHOLD
HOLDHOLD
HOLD: In this mode, the scanner will halt on a signal it encounters. It will not restart
automatically; you must manually re-initiate scanning if you wish to resume.
To set the Scan-Resume mode
c
Press the
[
F/L
]
key, then press the
[
0
(
SET
)
]
key, to enter the Set mode.
d
Rotate the DIAL to select Menu #7 (“
RESUMERESUME
RESUMERESUME
RESUME”).
e
Press the
[
F/L
]
key to enable changing of this Menu item.
f
Rotate the DIAL to select the desired scan-resume mode.
g
When you have made your selection, press the PTT key to save the new setting and
exit to normal operation.
The default condition for this Menu Item is “5 SEC”.
VFO SCANNING
This mode allows you to scan the entire current operating band.
c
Select the VFO mode by pressing the
[
VFO
(
PRI
)
]
key, if necessary.
d
Press and hold in the
[
(
MHz
)
]
or
[
(
MHz
)
]
key for 1/2 second to start scanning.
e
If and when the scanner encounters a signal strong enough to open the squelch, the
scanner will halt temporarily; the decimal point of the frequency display will blink
during this “Pause” condition.
f
The scanner will then resume according to the Scan Resume selected in the previous
section.
g
To cancel scanning, press the PTT key.
If you want to change direction of the scan while it is underway, rotate the DIAL one
click in the opposite direction (in this case, one click counter-clockwise).
Scanning
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-250R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-250R in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info