478472
27
Zoom out
Zoom in
Previous page
1/44
Next page
FT-250R OPERATING MANUAL 23
AUTOMATIC LAMP ILLUMINATION ON SCAN STOP
The FT-250R will automatically illuminate the LCD Lamp whenever the scanner stops
on a signal (the default condition for this feature is “ON”).
The procedure for disabling the Scan Lamp is:
c
Press the
[
F/L
]
key, then press the
[
0
(
SET
)
]
key, to enter the Set mode.
d
Rotate the DIAL to select Menu #8 (“
SCN LMPSCN LMP
SCN LMPSCN LMP
SCN LMP”).
e
Press the
[
F/L
]
key to enable changing of this Menu item.
f
Rotate the DIAL to set this Menu item to OFF.
g
When you have made your selection, press the PTT key to save the new setting and
exit to normal operation.
BAND EDGE BEEPER
The FT-250R will automatically “beep” when a band edge is encountered while tuning.
You may disable this feature, if it is annoying, without disabling the keypad beeper (the
default condition for this feature is “ON”).
The procedure for disabling the Band-Edge Beeper is:
c
Press the
[
F/L
]
key, then press the
[
0
(
SET
)
]
key, to enter the Set mode.
d
Rotate the DIAL to select Menu #17 (“
EDGE BPEDGE BP
EDGE BPEDGE BP
EDGE BP”).
e
Press the
[
F/L
]
key to enable changing of this Menu item.
f
Rotate the DIAL to set this Menu item to OFF.
g
When you have made your selection, press the PTT key to save the new setting and
exit to normal operation.
SMART SEARCH OPERATION
The Smart Search feature allows you to load frequencies automatically according to where
activity is encountered by your radio. When Smart Search is engaged, the transceiver will
search above and below your current frequency, storing active frequencies as it goes (without
stopping on them even momentarily); these frequencies are stored into a special Smart
Search memory bank, consisting of 31 memories (15 above the current frequency, 15
below the current frequency, plus the current frequency itself).
Two basic operating modes for Smart Search are available:
SINGLESINGLE
SINGLESINGLE
SINGLE: In this mode, the transceiver will sweep the current band once in each direc-
tion starting on the current frequency. All channels where activity is present
will be loaded into the Smart Search memories; whether or not all 31 memo-
ries are filled, the search will stop after one sweep in each direction.
CONTINUECONTINUE
CONTINUECONTINUE
CONTINUE: In this mode, the transceiver will make one pass in each direction as with
One-Shot searching; if all 31 channels are not filled after the first sweep,
however, the radio will continue sweeping until they are all filled.
Scanning
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-250R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-250R in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info