478472

Yaesu FT-250R Manual

26
Zoom out
Zoom in
Previous page
1/44
Next page
FT-250R OPERATING MANUAL22
MEMORY SCANNING
Memory scanning is similarly easy to initiate:
c
Set the radio to the Memory mode by pressing the
[
MR/MW
(
SKIP
)
]
key, if necessary.
d
Press and hold in the
[
(
MHz
)
]
/
[
(
MHz
)
]
key for 1/2 second to initiate scanning.
e
As with VFO scanning, the scanner will halt on any signal encountered that is strong
enough to open the squelch; it will then resume scanning according to the Scan-Re-
sume mode set previously.
f
To cancel scanning, press the PTT key.
H
OW
TO
S
KIP
(
O
MIT
)
A
C
HANNEL
D
URING
M
EMORY
S
CAN
O
PERATION
When you have some very active channels stored in memories, you may wish to skip them
when scanning, but still have them available for manual selection.
Such channels may be “Skipped” during scanning, if you like:
c
Set the radio to the Memory Mode by pressing the
[
MR/MW
(
SKIP
)
]
key, if necessary.
d
Rotate the DIAL to select the Memory Channel to be skipped during scanning.
e
Press the
[
F/L
]
key momentarily (not for 1/2 second), then press the
[
MR/MW
(
SKIP
)
]
key (momentarily). A small “SKIP” will appear to the LCD. indicating it is to be
ignored during scanning.
To re-institute the channel into the scanning loop, repeat the above three steps (the “Skipped”
channel will, of course, still be accessible via manual channel selection methods using the
DIAL in the MR mode).
PROGRAMMABLE
(
BAND LIMIT
)
M
EMORY SCAN
(
PMS
)
This feature allows you to set sub-band limits for either scanning or manual VFO opera-
tion. For example, you might wish to set up a limit (in North America) of 144.300 MHz to
148.000 MHz so as to prevent encroachment into the SSB/CW “Weak Signal” portion of
the band below 144.300 MHz. Here’s how to do this:
c
Set the radio to the VFO mode by pressing the
[
VFO
(
PRI
)
]
key, if necessary.
d
Using the techniques learned earlier, store (per the above example) 144.300 MHz into
Memory Channel #
L1L1
L1L1
L1 (the “
LL
LL
L” designates the Lower sub-band limit).
e
Likewise, store 148.000 MHz into Memory Channel #
U1U1
U1U1
U1 (the “
UU
UU
U” designates the Up-
per sub-band limit).
f
Switch to the Memory mode by pressing the
[
MR/MW
(
SKIP
)
]
key once, then rotate
the DIAL to select Memory Channel #
L1L1
L1L1
L1.
g
Press the
[
MR/MW
(
SKIP
)
]
key; the “
MRMR
MRMR
MR” label will be blinking in the left-hand fre-
quency of the display.
h
You may now rotate the DIAL, or begin scanning by pressing the
[
(
MHz
)
]
or
[
(
MHz
)
]
key for 1/2 second. The transceiver will behave as though it is in the standard VFO
mode, but operation will be restricted to the range between Memory Channels
L1L1
L1L1
L1 and
U1U1
U1U1
U1.
Note: Five pairs of Band Limit memories, labeled
L1L1
L1L1
L1/
U1U1
U1U1
U1 through
L5L5
L5L5
L5/
U5U5
U5U5
U5 are available.
Scanning
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-250R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-250R in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info