697438
41
Zoom out
Zoom in
Previous page
1/64
Next page
41
Commissioning
GREENSPRING CWi47 – 6 720 646 322 (2015/04)
9.3 Adjusting CO
2
(carbon dioxide)
When the gas pressure is correct:
Press ON/OFF button to turn off the appliance.
Remove brass flat head screw on the flue gas connector
(Fig.
57).
Fig. 57 Measuring port
▶Insert CO
2
analyzer probe into the test point. The tip of the
probe should be in the center of the flue pipe (inserted
approximately 60mm). Avoid air gaps between probe and
measuring port as they can alter readings.
While holding the Program (P) button, press the ON/OFF
button to turn ON the heater (Fig.
58).
Fig. 58
While holding the Program button, press the ON/OFF
button to turn ON the heater. As soon as ‘188’ flashes on
the display, release the Program button. The display should
now read P2.
▶Press or button until “P1” appears on display.
Measuring CO
2
(Combustion cover Installed):
Open all hot water taps to achieve a flow rate of at least 15
l/m (1 tub and 2 sinks are usually sufficient). If heater
display reverts back to P2, open more hot water fixtures to
allow sufficient flow.
▶Press until P1 reappears on the display.
Record the CO
2
reading in P1 in the Table 18.
Analyzer reading may take several minutes to stabilize.
▶Press button until P2 appears. Unit will ramp down to
low fire and the water flow should decrease.
Adjusting CO
2
If P1 CO
2
level is out of range:
Loosen yellow painted philips screw (Fig. 59,[1]) and
cover should rotate down (Fig.
59, [2]) revealing a
recessed brass slotted screw. (Fig.
59, [3]).
Turning the slotted screw counter clockwise.
P1 CO
2
levels, will increase.
Turning the slotted screw clockwise.
P1 CO
2
levels, will decrease.
After bringing the P1 CO
2
readings in proper range, press
the
button to enter the P2 mode.
The CO
2
shall only be adjusted by a Gas Safe
registered installer with a calibrated CO
2
analyzer.
CAUTION: Insufficient gas pressure
May affect CO
2
levels.
Check and adjust gas pressure
(Chapter
9.2).
6720646322-02.1V
CO2
O2
6720608920-19.1AL
Program CO
2
values
P1 __________%
P2 __________%
Table 18
Note: P1 adjustment will change the P2
reading. Confirm the P1 value BEFORE
adjusting the P2 level.
Adjustments to the slotted screw (P1) will
also change P2 CO
2
levels.
+
+
+
+
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worcester-Bosch GREENSPRING CWi47 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worcester-Bosch GREENSPRING CWi47 in the language / languages: English as an attachment in your email.

The manual is 5,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info