769323

Visonic Powermaster-360 Manual

37
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 37
(up to 40 digits string).
Note: To enter the APN Access Point, use the String Editor in section 4.8.1.
GPRS USERNAME
Enter the Username of the APN used for GPRS communications (up to 30 digits string).
Note: To enter the Username, use the String Editor in section 4.8.1.
SIM PIN CODE
Enter the PIN code of the SIM card installed in the GSM module (up to 8 numerical
digits).
Note: To enter the numerical PIN code, use the numerical keyboard.
GPRS PASSWORD
Enter the Password of the APN used for GPRS communications (up to 16 digits string).
Note: To enter the Password, use the String Editor in section 4.8.1.
NETWORK ROAMING
A new cellular roaming algorithm to support cases where the panel is successfully
connected to a network but GPRS connection has timed-out.
With the new roaming algorithm, in such cases the panel attempts to connect to a
different network.
Modem roam en: when selected, the panel uses the internal Cellular modem's
algorithm for roaming. (en) = enable
Roam disable: when selected, roaming is not allowed. Only the ‘Home’ network is
accepted.
Manual roam en : when selected, the panel uses its own algorithm to select the best
cellular operator.(en) = enable
Lock network: when selected, the panel uses the operator defined in Requested
Network. (en) = enable
REQUEST OPERATOR
Specifies a preferred network (for example, Vodafone) that the panel should attempt to
register with if the signal strength is above the Minimum CSQ value. Where a Requested
Operator is specified, the panel should attempt to return to this network on every other
attempt.
Note: Contains an editable line to enter up to 6 numbers MCC (Mobile country code)
+MNC (Mobile network code)
OP. BLACK LIST
Used to avoid certain networks, for example, when a high signal strength operator is
unreliable or the device oscillates between networks (country borders).
Note: Contains an editable line to enter up to 6 numbers MCC (Mobile country code)
+MNC (Mobile network code)”.
NETWORK TYPE
Define whether to use a 2G or 3G network or whether to enable the panel to use a 3G
network as first priority or a 2G network as second priority.
Options: automatic (default); 3G; 2G.
GPRS ALWAYS ON
Define whether the control panel will stay continuously connected enabled, via GPRS
communication, or disconnect disabled (default), after each report session.
GSM KEEP ALIVE
Some GSM Service providers tend to disconnect the GSM connection if the user has not
initiated any outgoing telephone calls during the last 28 days. To prevent from
disconnecting the GSM connection, you can configure the system to generate a keep
alive GSM call every 28 days sending a test message either to the first SMS number (if
exists) or alternatively first private telephone number.
Options: Disable (default) or Every 28 days.
TRANS. PROTOCOL
Select the IP protocol used to transfer data over the internet/GPRS.
Options: TCP (default); or UDP.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info