769323
39
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 39
Option
Configuration Instructions
12:RCVR2 ACCOUNT
your specific alarm system to the 1st Monitoring Station (designated as RCVR1 or RCV1) and a
2nd Account (subscriber) number (12:RCVR 2 ACCOUNT) that will identify the system to the 2nd
Monitoring Station (designated as RCVR2 or RCV2). Each of the Account numbers consists of
6 hexadecimal digits.
Master Installer only
To enter Hexadecimal digits, use the following table:
Entering Hexadecimal Digits
Digit
0…..9
A
B
C
D
E
F
Keying
0…..9
[#][0]
[#][1]
[#][2]
[#][3]
[#][4]
[#][5]
21:IP RCVR 1
22:IP RCVR 2
Master Installer only
The PowerMaster-360 can be programmed to report the event messages defined in Report
Events option (option 01) to two IP Receivers, Visonic PowerManage model. IP reporting can be
performed via GPRS (IP) channel using SIA IP format or via Broadband IP channel using SIA IP.
Enter the two IP addresses (000.000.000.000) of the IP Receiver 1 located at the 1st Monitoring
Station (21:IP RCVR 1) and IP Receiver 2 located at the 2nd Monitoring Station (22:IP RCVR 2).
Note: You must enter the IP address of the receiver, even if you enter the Domain Name System
(DNS) server name where the receiver is installed. See option 28: RCVR 1 DNS and 29: RCVR 2
DNS for details on how to enter the DNS name.
26:SMS RCVR 1
27:SMS RCVR 2
Master Installer only
If equipped with GSM module, the PowerMaster-360 can be programmed to report the event
messages defined in Report Events option (option 01) to two SMS Receivers via the GSM
SMS channel using a special SMS text format. For further details concerning the SMS text
format please contact Visonic.
Enter the two telephone numbers (including area code – maximum 16 digits).of the SMS
Receiver 1 located at the 1st Monitoring Station (26:SMS RCVR 1) and SMS Receiver 2
located at the 2nd Monitoring Station (27:SMS RCVR 2).
Note: To enter the international prefix (
) at the 1st digit – key-in [#]
[1].
28:RCVR 1 DNS
29:RCVR 2 DNS
Master Installer only
Specifies the DNS name of the servers where the IP receivers are installed. Enter the DNS
name of the servers where receiver 1 and receiver 2 are installed; the name can contain a
maximum of 32 characters. The DNS name one (28: RCVR 1 DNS) must be resolved to IP
receiver one (21: IP RCVR1) and the DNS name two (29: RCVR 2 DNS) must be resolved to
IP receiver two (22: IP RCVR2).
Note: If you enter the DNS name you must also enter the corresponding IP receiver’s address.
See option 21: IP RCVR 1 and 22: IP RCVR 2 for details on how to enter the IP receiver’s
address.
47:GSM RETRIES
Define the number of times the system will retry to report to the Monitoring Station in case of
failure to report via the cellular connection - GPRS (IP) and SMS.
Options: 2 attempts; 4 attempts (default); 8 attempts; 12 attempts and 16 attempts.
48:BB IP RETRIES
Define the number of times the system will retry to report to the Monitoring Station in case of
failure to report via the Broadband Module connection.
Options: 2 attempts; 4 attempts (default); 8 attempts; 12 attempts and 16 attempts.
51: AUTO-TST LOOP
To verify a proper communication channel, the PowerMaster-360 can be configured to send a
test event to the Monitoring Station periodically. You can set the interval between the consecutive
test events or disable the automatic sending of this event entirely. If the interval is set for every
one day or more then the exact hour of reporting can be selected with option 52.
Options: test OFF (default); every 1/2/5/7/14/30 day(s); and every 5 hours.
52:AUTO TST TIME
Enter the exact time (auto test time) during the day at which the Auto Test message (if
enabled in option 51) will be sent to the Monitoring Station.
Note: If the AM/PM format is used, you can set the AM digit with the button and the
PM digit with the button.
53:COM.FAIL RPRT
Determine whether a failure in the system communication channel i.e. GSM/GPRS will be
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info